View
3
Download
0
Category
Preview:
Citation preview
Stereo Control 035 86
Part. U2695C - 09/09-01 PC
Notice d’installationInstallation manual
Français 3FR
English 11UK
3
Table des matièresFR
1 - Introduction __________________________________________________ 41.1 - Avertissements et conseils __________________________________________ 41.2 - Contenu de l’emballage ____________________________________________ 41.3 - Description générale ______________________________________________ 5
2 - Installation __________________________________________________ 62.1 - Schéma de branchement ___________________________________________ 6
3 - Configuration _________________________________________________ 83.1 - Programmation __________________________________________________ 83.2 - Rétablissement ___________________________________________________ 8
4 - Éventuels problèmes et solutions ____________________________________ 9
4
1 - Introduction
1.1 - Avertissements et conseils
Avant de procéder à l’installation du module, il est important de lire attentivement la présente notice.
Le fabricant décline toute responsabilité en cas de dommages causés par une mauvaise utilisation et/ou une utilisation non conforme aux instructions figurant dans la présente notice.
1.2 - Contenu de l’emballage
L’emballage du Contrôle Stéréo contient:
c Contrôle Stéréo 035 86
c Câble avec émetteur IR
c Câble RCA-RCA
c Câble du connexion au bus (2 mètres)
c Instructions d’utilisation
c CD
5
1.3 - Description générale
Le Contrôle Stéréo est un dispositif qui permet l’interfaçage, l’isolation, l’adaptation de niveau et le contrôle à travers des signaux infrarouges entre une source stéréo externe et le BUS de diffusion sonore.Le dispositif permet de mémoriser et de dupliquer des codes de télécommande à infrarouges sur une plage de fonctionnement comprise entre 30 Khz et 80 Khz.Contrôler attentivement cette caractéristique et au besoin contacter l’assistance technique Legrand pour s’assurer de la compatibilité.
1 - Introduction
8
7
6
1
2
345
Legend1 Entrée audio stéréo avec double
connecteur RCA2 Boutons d’équilibrage du signal3 Voyant d’équilibrage du signal4 Voyant d’alimentation5 Capteur infrarouge6 Connecteur USB7 Connecteur 3,5 mm pour câble
avec émetteur IR8 Connecteur 8 pôles pour BUS de
diffusion sonore
VOYANT ALIMENTATION (7)
VERT Stand/by
JAUNE On
VOYANT ÉQUILIBRAGE SIGNAL (8)
ÉTEINT Absence de signal
VERT Présence de signal audio
VERT (1) Réglage optimal
ORANGE (2) Signal trop élevé
(1) clignotant ORANGE sur les seuls pics(2) ORANGE persistant
Tableau voyants IndICATeURS
6
2.1 - Schéma de branchement
Installer le câble avec émetteur IR, en appliquant la partie adhésive de l’émetteur à proximité (à une distance max. de 1 cm) du récepteur IR de la source (ne pas brancher l’émetteur au-dessus du récepteur IR). La distance maximum entre le dispositif et la source est de 1 m.
2 - Installation
5 6 7 8
Émetteur IR adhésif
Capteur IR source stéréo
Câble BUS longueur 2 m (fourni)
Câble avec émetteur IR longueur 1,8 m (fourni)
Contrôle stéréo035 86
Câble RCA/RCA(fourni)
Bus diffusion sonoreBornes 5 et 6
Attention: ne pas augmenter la longueur du câble à émetteur IR.En cas d’utilisation de la sortie casque du système Hi-Fi, veiller à bien régler le volume.
7
2 - Installation
c Avant d’effectuer la programmation du Contrôle Stéréo, s’assurer que les piles de la télé-commande du système Hi-Fi sont suffisamment chargées.
c Contrôler la position du voyant de réception du système Hi-Fi et positionner le câble à émetteur IR à une distance maximum de 1 cm par rapport à celui-ci
c S’assurer de la présence d’un seul voyant sur le système Hi-Fi (il n’est pas possible de contrôler plusieurs voyants - sources).
c Durant l’utilisation du Contrôle Stéréo, ne pas utiliser la télécommande du système Hi-Fi.
c La capacité d’apprentissage du Contrôle Stéréo est comprise entre 30 Khz et 80 Khz, hors de cette plage le fonctionnement n’est pas garanti.
Compte tenu des constantes évolutions technologiques et fonctionnelles (télécommandes à infrarouges) des systèmes Hi-Fi, le fabricant conseille de s’assurer, auprès du Centre d’appel ou du Centre d’assistance technique le plus proche, de la compatibilité du dispositif.
RECOMMANDATIONS
8
S = 1 – 4 adresse du dispositif au sein du système
M1 = 1 – 4 (indiquer le nombre de modules de l’installation Hi-Fi - ex.radio, cd, etc. - que le Contrôle Stéréo doit gérer).
Brancher le câble du BUS et ensuite le câble RCA-RCA et le jack de l’IR.
3 - Configuration
Avant de procéder à la programmation du Contrôle Stéréo (il ne doit pas être branché au BUS):
3.1 - Programmation
Pour programmer la référence 035 86, utiliser le logiciel StereoControlConfig présent sur le CD fourni, en faisant référence au manuel correspondant.
3.2 - Rétablissement
Pour rétablir les réglages usine, procéder comme suit:
- Couper l’alimentation du Contrôle Stéréo
- Configurer: S = –; M1 = –; M2 = 9
- Rétablir l’alimentation du dispositif et attendre que le voyant 3 s’allume
- Couper l’alimentation et rétablir la configuration
En cas d’utilisation de la matrice multicanal 035 86, il est possible de gérer un seulmodule du système Hi-Fi. Configurer par conséquent M1 = 1.
9
4 - Éventuels problèmes et solutions
PROBLÈME CAUSE SOLUTION
Le voyant ON/OFF (indicateur d’état) ne s’allume pas
Alimentateur installation en protection.
Contrôler et éliminer la cause du court-circuit.Charger l’alimentateur.
Absence de tension 27 Vdc sur la borne BUS de l’alimentateur.
S’assurer de la présence de tension 24 – 27 Vdc sur la sortie OUT du nœud A/V de connexion. En cas d’absence de tension, éliminer le court-circuit du BUS sur le côté du nœud A/V
Le système Hi-Fi n’est pas commandé via IR Mauvais branchement du câble IR.
Contrôler et corriger le câblage:le câble à émetteur IR doit se trouver à 1 cm du récepteur IR du système Hi-Fi à contrôler.
Quand le système Hi-Fi est allumé, le voyant ADJ reste éteint.
Signal audio absent. S’assurer de la présence dusignal audio.
Signal audio très faible.
Contrôler le réglage du poten-tiomètre d’adaptation du niveau ou augmenter le niveau du signal fourni par la source externe.
Le voyant de niveau reste rouge. Procéder au réglage du poten-tiomètre d’adaptation du niveau.
Distorsion du signal reproduit y compris à faible volume.
S’assurer que le voyant de niveau ne devient pas orange durant la reproduction des morceaux. Régler le potentiomètre du système Hi-Fi allumé de telle sorte que le voyant soit toujours vert (seuls de brefs allumages de couleur orange sont admis lors des pics musicaux).
10
Appendice
Caractéristiques techniques Contrôle Stéréo 035 86
CARACTÉRISTIQUES TECHNIQUES
Tension d’alimentation 18 – 27 Vdc
Absorption en stand-by 20 mA (max)
Absorption en fonctionnement 40 mA (max)
Température de fonctionnement 5 – 35 °C
CARACTÉRISTIQUES AUDIO STÉRÉO
Impédance d’entrée RCA 14 Kohm
Sensibilité d’entrée 200 mVrms – 1 Vrms
Équilibrage canaux TYP ± 0.5 dB
Équilibrage canaux MIN ± 1.5 dB
Réponse en fréquence @ -3 dB 20 Hz – 20 Khz (de l’intégralité du transfert, mesurée sur la sortie de l’amplificateur).
CARACTÉRISTIQUES SIGNAUx INFRAROUGES
Capacité d’apprentissage 30 Khz – 80 Khz (hors de cette plage le fonctionnement n’est pas garanti).
11
ContentsUK
1 - Introduction _________________________________________________ 121.1 - Warnings and tips__ ______________________________________________ 121.2 - Package content _________________________________________________ 121.3 - General description ______________________________________________ 13
2 - Installation _________________________________________________ 142.1 - Wiring diagram __________________________________________________ 14
3 - Configuration ________________________________________________ 163.1 - Programming ___________________________________________________ 163.2 - Reset __________________________________________________________ 16
4 - Troubleshooting ______________________________________________ 17Appendix ___________________________________________________________ 18
12
1 - Introduction
1.1 - Warnings and tips
Before installing the module read this manual carefully.
The manufacturer declines all responsibility for any damage due to incorrect use and/or use which does not conform to the instructions of this manual.
1.2 - Package content
The Stereo Control package contains:
c Stereo Control 035 86
c Cable with IR transmitter
c RCA-RCA cable
c Cable for connection to the BUS (2 metres)
c Instruction sheet
c CD
13
1.3 - General description
The Stereo Control is a device which allows the interfacing, insulation, level adaptation and control via infrared signals between an external stereo source and the sound system BUS.The item enables you to store and replicate infrared remote control codes with an operating range between 30Khz and 80Khz. Carefully check this feature and if necessary contact Legrand’s technical assistance to verify its compatibility.
1 - Introduction
8
7
6
1
2
345
POWER SUPPLY LED (4)
GREEN Stand by
YELLOW On
SIGNAL BALANCE LED (3)
OFF No signal
GREEN Audio signal present
GREEN(1) Best setting
ORANGE(2) Signal too high
(1) ORANGE flashing on the peaks only(2) Continuous ORANGE
Led indication tables
LEGEND1 Audio stereo input with double
RCA connector2 Signal balance pushbuttons3 Signal balance LED4 Power supply LED5 Infrared detector6 USB Connector7 3.5 mm connector for cable with
IR transmitter8 8-pole connector for sound
system BUS
14
2.1 - Wiring diagram
Install the cable with IR transmitter, applying the adhesive part of the transmitter close (max 1 cm) to the source IR receiver (do not connect the transmitter above the IR receiver). The maximum distance between the device and the source must be 1 m.
2 - Installation
5 6 7 8
Adhesive IR transmitter
Stereo source IR detector
2 m long BUS cable (supplied)
1.8 m long cable with IR transmitter(supplied)
Stereo control035 86
RCA/RCA cable (supplied)
Sound system BUSTerminals 5 and 6
Please note: do not increase the cable length with an IR transmitter. If you use the Hi-fi system headphone output, mind the level of the volume.
15
2 - Installation
c Before programming the Stereo Control, make sure that the remote control batteries of your Hi-Fi are sufficiently charged.
c Check the position of the Hi-Fi system LED and place the cable with the IR transmitter at a maximum distance of 1 cm from it.
c Make sure there is only one Hi-Fi LED (it is not possible to manage several source-LEDs).
c When using the Stereo Control, do not use the remote control of the Hi-fi system.
c The pickup capacity of the Stereo Control is between 30 Khz and 80 Khz; operation outside this range is not guaranteed.
Given the continuous technical and functional developments (infrared remote controls) of Hi-Fi systems, the manufacturer recommends to check the compatibility of the device. To do so, please contact the Call Centre or your nearest Technical Service Centre.
WARNINGS
16
S = 1 – 4 device address in the system
M1 =1 – 4 (indicate the number of Hi-Fi system modules, e.g. Radio, CD…, which the Stereo Control must manage)
Connect the BUS cable and then the RCA-RCA cable and the IR jack.
3 - Configuration
Before programming the Stereo Control (it must not be connected to the BUS):
3.1 - Programming
To program item 035 86 use the StereoControlConfig software supplied in the CD which comes with the device, referring to its manual.
3.2 - Reset
Restore the factory settings as follows:
- Switch the Stereo Control off
- Configure: S = – ; M1 = – ; M2 = 9
- Switch the device back on and wait for LED 3 to light up
- Switch off and restore the configuration
If the multi-channel matrix (035 84) is used, only one Hi-Fi system module can be managed, so configure M1=1.
17
4 - Troubleshooting
PROBLEM CAUSE SOLUTION
The ON/OFF LED (status indicator) does not light up
Power supply unit in protection mode.
Check and eliminate the cause of the short-circuit.Replace the power supply unit.
No 27 Vdc on the BUS terminal of the power supply unit.
Make sure there is 24 – 27 Vdc at the OUTPUT of the A/V Node to which it is connected. If there is no voltage, eliminate the short-circuit on the BUS (at the OUT side of the A/V Node).
The Hi-Fi system is not controlled via IR Incorrect IR cable wiring.
Check and correct wiring the cable with the IR transmitter must be placed at a distance of 1 cm from the IR receiver of the Hi-Fi system to be managed.
The ADJ LED stays off when the Hi-Fi system is active
Audio signal missing. Check if there is an audio signal.
Very low audio Signal.
Check the adjustment of the level potentiometer or increase the level of the signal given by the external source.
The level LED is always red. Adjust the level potentiometer correctly.
The signal is distorted, even at low volumes.
Make sure the level LED does not turn orange when playing tracks. Adjust the potentiometer of the active Hi-Fi system so that the LED is always green (it can only turn orange for a very short time, during musical peaks).
18
Appendix
Technical data Stereo Control 035 86
RATING PLATE DATA
Supply voltage: 18 – 27 Vdc
Absorption in stand-by 20 mA (max)
Absorption in operation 40 mA (max)
Operating temperature 5 – 35 °C
AUDIO STEREO FEATURES
RCA input impedance 14 Kohm
Input sensitivity 200 mVrms – 1 Vrms
Balancing TYP channels ± 0.5 dB
Balancing MIN channels ± 1.5 dB
Frequency range @ -3 dB 20 Hz – 20 Khz (of the entire transfer, measured on the amplifier output).
INFRARED SIGNAL FEATURES
Learning capacity 30 Khz – 80 Khz (operation outside this range is not guaranteed).
World Headquarters andInternational Department87045 LIMOGES CEDEX FRANCE
: 33 5 55 06 87 87Fax : 33 5 55 06 74 55www.legrandelectric.com
Legrand reserves at any time the right to modify the contents of this booklet and to communicate, in any form and modality, the changes brought to the same.
Recommended