1
Linkedin Profile: https://www.linkedin.com/profile/view?id=376492318&trk=nav_responsive_tab_profile Muhammad Umar Block no F5,Flat no 15 Majeed SRE National stadium road Karachi. Phone Number: 03312721722 / 03150261216 Email: [email protected], [email protected] PEC Registration Number Elect-47470 HONORS AND SCHOLARSHIPS Cum laude B.E 3 rd semester Federal Govt. educational scholarship throughout the engineering EXTRA CURRICULAR ACTIVITES Represented the college in inter board swimming championship. Organized orientation Sessions for Engineering Students Organized the Session for Islamic Preach by Mr Junaid Jamshed for Bahria University MAJOR COURSES Instrumentation & Measurements Liner Control Systems Non Linear Control Systems Digital Data Aquisition and Control Signals & Systems Digital Signal Processing Advance Digital signal Processing Embedded Systems(FPGA, Raspberry Pi) Electrical Network Analysis Industrial Automation(PLC, HMI, VFD) Electromechanical System Electronic Devices and Circuits 1&2 Micro Processor Computer Architecture Opto Electronics Data Communication & Networking Engineering Ethics ACADEMIC PROJECTS Final year project: PLC Based Automatic Feed Control System Via HMI PCB fabrication of dual power supply Obstacle avoiding car using ultrasonic Sensor and 8051 Raspberry Pi based 4WD Robot CAREER OBJECTIVES To work passionately in a progressive environment where I can implement and enhance my knowledge and skills to serve the firm effectively. NTS GAT Percentile 84.27% ( Appeared on 5th July 2015 ) EDUCATION Fall 2015-Now MS (Control systems) with 3.5 CGPA From NUST PNEC Karachi 2010-2014 BE Electrical(Electronics) with 3.15 CGPA From Bahria Uiversity (PEC Recognized) 2008-2010 HSSC Govt. Degree College Majeed SRE National Stadium Road Karachi (65.7%) 2006-2008 Ebrahim Ali Bhai PN Boys Sec School Majeed SRE Karachi (82.7%) WORK EXPERIENCE (Total 3 year 8 Months) Controls & Automaion Engineer in Cheetal Technology (Mar 2015 - Current) Representing linkwise technology in Pakistan as Cheetal technology.Working on PicoBox Data Acquisition modules in the SCADA environment using MCONEX a full SCADA Software and provide monitoring systems and controls as well as remote monitoring is also provided. Works on Modbus Protocol. Design Engineer in Platinum Engineering (Aug 2011- Sep 2014) Industrial automation project based work, I did some projects for them. Trainee in Lucky Cement Limited (June-July 2013) Instrumentation, DCS & SCADA systems Internee in Paktherm Private Ltd (June-Aug 2011) Transformers, Power supplies, Thyristor controlled rectifiers & Autocad drawings. DEVELOPMENT TOOLS & TECHNICAL SKILLS Certified Courses: PLC,HMI,DCS Basic Training: Raspberry Pi, Microcontrollers & FPGA Languages: C++, C#, Assembly, VB Script, Verilog, Ladder, Instruction Set and FBD Tools and Techniques: Autocad, orcad, Matlab, SIMATIC,WPL Soft, DOP soft, Multisim, Circuit Wizard, Xilinx, MS Office and Adobe Photoshop.

Muhammad Umar BEE pdf

Embed Size (px)

Citation preview

Page 1: Muhammad Umar BEE pdf

Linkedin Profile: https://www.linkedin.com/profile/view?id=376492318&trk=nav_responsive_tab_profile

Muhammad Umar Block no F5,Flat no 15 Majeed SRE National stadium road Karachi. Phone Number: 03312721722 / 03150261216 Email: [email protected],

[email protected]

PEC Registration Number

Elect-47470

HONORS AND SCHOLARSHIPS Cum laude B.E 3rd semester

Federal Govt. educational scholarship throughout the engineering

EXTRA CURRICULAR ACTIVITES Represented the college in inter

board swimming championship.

Organized orientation Sessions for Engineering Students

Organized the Session for Islamic Preach by Mr Junaid Jamshed for Bahria University

MAJOR COURSES Instrumentation & Measurements

Liner Control Systems

Non Linear Control Systems

Digital Data Aquisition and Control

Signals & Systems

Digital Signal Processing

Advance Digital signal Processing

Embedded Systems(FPGA, Raspberry Pi)

Electrical Network Analysis

Industrial Automation(PLC, HMI, VFD)

Electromechanical System

Electronic Devices and Circuits 1&2

Micro Processor

Computer Architecture

Opto Electronics

Data Communication & Networking

Engineering Ethics

ACADEMIC PROJECTS Final year project: PLC Based Automatic

Feed Control System Via HMI

PCB fabrication of dual power supply

Obstacle avoiding car using ultrasonic Sensor and 8051

Raspberry Pi based 4WD Robot

CAREER OBJECTIVES To work passionately in a progressive environment where I can implement and enhance my knowledge and skills to serve the firm effectively.

NTS GAT Percentile 84.27% ( Appeared on 5th July 2015 ) EDUCATION Fall 2015-Now MS (Control systems) with 3.5 CGPA From NUST PNEC Karachi 2010-2014 BE Electrical(Electronics) with 3.15 CGPA From Bahria Uiversity (PEC Recognized) 2008-2010 HSSC Govt. Degree College Majeed SRE National Stadium Road Karachi (65.7%) 2006-2008 Ebrahim Ali Bhai PN Boys Sec School Majeed SRE Karachi (82.7%)

WORK EXPERIENCE (Total 3 year 8

Months) Controls & Automaion Engineer in Cheetal

Technology (Mar 2015 - Current) Representing linkwise technology in Pakistan as Cheetal technology.Working on PicoBox Data Acquisition modules in the SCADA environment using MCONEX a full SCADA Software and provide monitoring systems and controls as well as remote monitoring is also provided. Works on Modbus Protocol.

Design Engineer in Platinum Engineering (Aug 2011-Sep 2014) Industrial automation project based work, I did some projects

for them.

Trainee in Lucky Cement Limited (June-July 2013) Instrumentation, DCS & SCADA systems

Internee in Paktherm Private Ltd (June-Aug 2011) Transformers, Power supplies, Thyristor controlled rectifiers & Autocad drawings.

DEVELOPMENT TOOLS & TECHNICAL SKILLS Certified Courses: PLC,HMI,DCS

Basic Training: Raspberry Pi, Microcontrollers & FPGA

Languages: C++, C#, Assembly, VB Script, Verilog, Ladder, Instruction Set and FBD

Tools and Techniques: Autocad, orcad, Matlab, SIMATIC,WPL Soft, DOP soft, Multisim, Circuit Wizard, Xilinx, MS Office and Adobe Photoshop.