Installation Instructions · 2020-03-11 · Installation Instructions A CommScope Company put barcode here 05 RE F Andrew Institute offers installation training. Andrew Wireless Solutions

G

R

Q

Tower Mount for 6ft (1.8m) Antennas.

102344

GRE06

Bulletin

RevStatusModel Version

Version RevStatus

1 of 13page

Installation Instructions A CommScope Company

put barcode here

FRE05

Andrew Institute offers installation training.

Andrew Wireless Solutions

Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.

Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by

Other Europe: +44 592 782 612 U.K.: 0800 250055 or 1-888-235-5732U.S.A., Canada, Mexico: 1-800-255-1479Customer Service 24 hours

® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement anyspecifications or warranties relating to Andrew Wireless Solutions products or services.

www.andrew.com

Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.

TMW Antenna

3

1 REFLECTOR ASSY

D

** =2 STRUTS FOR HIGH WIND LOAD ONLY.

TABLE 2- FASTENER TORQUE SPECIFICATIONS

TABLE 1- ANTENNA PARTS LIST

* = PART OF ACCESSORY KIT

!

U-BOLT

E 2 BRACKET

G 1 PANNING FRAME ASSY

H 1 AZIMUTH ADJUSTER

I 1 ELEVATION ADJUSTER

N 11 M12x35mm HEX HEAD BOLT*

19 FLAT WASHER*

11

and zinc dust.regulations for petroleum products. Contents: oil, clay, partially filled containers according to governmental open near food or food sources. Dispose of empty or amounts of liquid soap and rinse with water. Do not store away from mouth. Wash thoroughly after use with liberal the pre-applied conductive grease on threads. Keep Warning: Use protective wear to avoid skin contact with

results of improper or unsafe installation practices.Andrew disclaims any liability or responsibility for the

installation, maintenance, and condition of equipment.once a year by qualified personnel to verify proper such personnel. Antenna systems should be inspected Andrew installation instructions have been written for systems requires qualified, experienced personnel. The installation, maintenance, or removal of antenna Notice

elevation adjustment.This mount provides ±12° azimuth or ±15° pipe of diameter 48 to 115 mm (1.9 to 4.5"). assemble and fit the antenna mount to a vertical tower The following pages show the steps required to Description

SPRING WASHER*

11 M12 NUT*

Q 1 MOUNTING ANGLE

R 1 STRENGTHENING STRUT

S 1** STRUT PIPE

T 1 SAFETY BRACKET

Item Qty. Description

A

Fastener Material

Torque values in Nm (lb.ft)

Fastener size- M5 M6 M8 M10 M12 M16

Stainless Steel

4.5 7.7 18.7 39.2 65.1 161(3.3) (5.7) (13.8) (28.9) (48) (18.7)

Galvanized2.7 4.5 11.1 22 38 95

(2.0) (3.3) (8.1) (16.2) (28) (70.1)

S

A

D

I

E

NH

T


102344

GRE06

Bulletin


Version RevStatus

2 of 13page


FRE05




Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by


® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement anyspecifications or warranties relating to Andrew Wireless Solutions products or services.

www.andrew.com


TMW Antenna

showing appropriate sections

Note:-only the left side assembly is described the right side assembly is identical except or

the antenna may be assembled with the mounts

Certain views have the antenna shields omitted for clarity.

the orientation of the strengthening strut - alternate steps and views will be shown.

on the right or the left side of the poles as shown.

The image shown can vary from product to product. Specific views will be display

Assembling the Mount

Mount Assembled onRight Hand Side

Mount Assembled onLeft Hand Side

L.H.S. Assembly

Orientation of Strengthening Strut Pipe on Mount

is fitted to the Top of the Reflector Backing Ring, as shown.

For mounts assembled on the Left Hand Side - the strengthening strut item (R) 1.is fitted to the Bottom of Reflector Backing Ring, as shown.

For mounts assembled on the Right Hand Side - the strengthening strut item (R) 2.

R.H.S. Assembly

Strengthening StrutStrengthening Strut

Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.

102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


3 of 13page


FRE05



© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by ® or ™ are registered trademarks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any


specifications or warranties relating to Andrew Wireless Solutions products or services.

www.andrew.com

Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.

TORQUE TO 38NmG

R

N

N N

TORQUE TO 38Nm

A

Q

N

TORQUE TO 38Nm


102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


4 of 13page


FRE05






www.andrew.com


tighten the bolts to the recommended torque.

1. Fit the mounting bracket (Q) to the backing ring using fixing (N) tighten bolts to the recommended torque.2. Fit the panning frame assy (G) to the mounting bracket (Q) using the fixings (N) tighten the bolts to the recommended torque.L.H.S. Mount only.3. Fit the Strengthening Strut (R) to Mount using fixings (N)

Mount Assembly

for rotational movement whilst remaining securly attached.

Fit elevation adjuster (I) to the position shown on the mount (G).1.Tighten all bolts and nuts to the elevation adjuster securely enough to allow 2.

Attaching the Elevation Adjuster


102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


5 of 13page


FRE05






www.andrew.com


TORQUE TO 38Nm

I

G

TO THREADSAPPLY GREASE

ENSURE ELEVATION ADJUSTER IS FITTED AT TOP OF MOUNT


102344

GRE06

Bulletin


Version RevStatus

TMW ANTENNA

TOWER MOUNT FOR 6ft (1.8m) ANTENNAS.

6 of 13page


FRE05






www.andrew.com


ATTACH SAFETY BRACKET

TORQUE TO 95Nm

1. Lift the Antenna using the hoisting hole located on the backing ring

Never walk under hoisted loads

2.

Attach Antenna to the pole

fully tighten U-Bolts to recommeded torque.

Attach Mount to pole using U-Bolts, 1.once in approximate position,

WARNING

Lifting the Antenna Mount on L.H.S.


102344

GRE06 RevStatusModel Version

Version RevStatus

TMW Antenna


7 of 13page


FRE05


Andrew Wireless SolutionsVisit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.© 2008 CommScope, Inc. All rights reserved.Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by ® or ™ are registered trademarks or trade-


marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement anyspecifications or warranties relating to Andrew Wireless Solutions products or services.

www.andrew.com


Bulletin

TORQUE TO 95Nm

TORQUE TO 95Nm

Never walk under hoisted loads

2. Attach Strenthening Strut (R) to Mount using Fixings (N)

1. Lift the Antenna using the hoisting hole located on the backing ring

Attach Antenna to the pole

tighten the bolts to the recommended torque.

Attach Mount to pole using U-Bolts, once in approximate position, 1.fully tighten U-Bolts to recommeded torque.

WARNING

Lifting the Antenna Mount on R.H.S.


102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


8 of 13page


FRE05






www.andrew.com


TORQUE TO 95Nm

TORQUE TO 95Nm

SUPPORT

ES

APPROVED STRUCTURAL

H

APPLY GREASE TO THREADS

ENSURE BRACKET ANDNUT ARE BOLTED RIGIDLYTOGETHER WITH APPROVEDSTRUCTURAL SUPPORT AS SHOWN.(VIEWED FROM ARROW 'A')

BRACKET

SUPPORTAPPROVED STRUCTURAL NUT TO BE TIGHT

STRUCTURAL SUPPORTAPPROVED TO BRACKET AND

'A'

RECOMMENDED TORQUE.

2. Attach Strut Pipe (S) to Bracket with Fixing (N)3. Attach the Azimuth Adjuster (H) to the Strut Pipe (S). 4. Attach the Azimuth Adjuster (H) to approved structural support using the Clamp Bracket

Attaching the Azimuth Adjuster

fitted on Azimth Adjuster.

Assemble Brackets (E) together with Fixings (N), attach to Reflector Assembly, 1.as shown with Fixings (N).

STRUT TO BE LOOSELY FITTED UNTIL ALIGNMENT IS COMPLETETHEN TIGHTEN FIXINGS TO


102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


9 of 13page


FRE05






www.andrew.com



102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


10 of 13page


FRE05






www.andrew.com


3. Attach the Clamp Bracket (H) to the Strut Pipe (S). 4. Attach the Clamp Bracket (H) to approved structural support using the Pipe Clamp Bracket .

Attaching Second Strut Pipe

5. Ensure Brackets and Nuts are bolted rigidly together as shown on previous page.

Assemble Bracket (E) and Fixings (N), attach to Reflector Assembly, 1.2. Attach Strut Pipe (S) to Bracket with Fixing (N)

STRUT TO BE LOOSELY FITTED UNTIL ALIGNMENT IS COMPLETE THEN TIGHTEN FIXINGS TO RECOMMENDED TORQUE.

H

E

S

N

Second Strut attachment position for Left Hand Mount

Approved structuralsupport



102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


11 of 13page


FRE05






www.andrew.com


3. Re-torque fixings once adjustemnt is complete.

Adjusting the Antenna in Elevation

Loosen the 5 bolts on the Panning Frame Assembly enough to allow for 1.rotational movement while remaining securley attached.Loosen the nuts on the Fine Elevation Adjuster and adjust the antennas signal,2.until the optimum signal is found. Tighten the nut on the Fine Adjuster by hand.

Antenna set-up and alignment

±15°ADJUSTMENT ELEVATION

TORQUE TO 38Nm

ENSURE SAFETY BRACKET IS SECURELY FITTED AT ALL TIMES

LOOSEN NUT/BOLTBEFORE ELEVATIONADJUSTMENT - RETORQUE TO 38Nm

Note:

LOOSEN NUTS ON U-BOLT BEFORE AZ. ADJUSTMENT - RETORQUE TO 38Nm

prior to adjsutment.must be fitted Strengthening Strut (R)

±12°ADJUSTMENT AZIMUTH

TORQUE TO 95Nm

LOOSEN NUTS ON BRACKETS BEFORE AZ. ADJUSTMENT - RETORQUE TO 38Nm

4. Repeat ELEVATION and AZIMUTH adjustments until optimum signal is found.

Loosen the U-Bolts enough to allow for rotational movement around the pole,1.while remaining securley attached.

2. Loosen the nuts on the Azimuth adjuster and adjust the antennas signal, until the optimum signal is found. Tighten the nut on the fine adjuster by hand.3. Re-torque fixings once adjustemnt is complete.

Adjusting the Antenna in Azimuth


102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


12 of 13page


FRE05






www.andrew.com


25

255

5


102344

GRE06

Bulletin


Version RevStatus

TMW Antenna


13 of 13page


FRE05






www.andrew.com


Attaching the clamp bracket to the side strut

the angular limits shown in

Side Strut & Clamp Bracket installation

the illustrations.

NOTE:The side strut must be attached pointing directly behind the antenna within

1. Tighten M12 U-Bolt sufficiently to allow for movement whilst remaining securely attached

Azimuth Adjuster

TORQUE TO 95Nm

S

Clamp Bracket on


Documents

Installation Instructions · 2020-03-11 · Installation Instructions A CommScope Company put barcode here 05 RE F Andrew Institute offers installation training. Andrew Wireless Solutions