Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
DDRC810DT-GL
RJ12 215 mm (8.46 in)
93
mm
(3
.66
in)
103
mm
(4
.06
in)
64 mm (2.52 in)
145 mm(2 in)
45 mm(2 in)
Relay Controller
www.lighting.philips.com/dynalite
Installation Instructions
Instructions d’installation
Installationsanweisungen
Instrucciones de instalación
Istruzioni per l’installazione
Installatie-instructies
インストール手順安装指示
50° C (122° F)
-5° C (23° F)
≤90%
IEC Pollution Degree II
Devices must be installed in an approved enclosure by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
Les appareils doivent être installés dans un lieu jugé apte, par un électricien qualifié et conformément aux règles et normes locales et nationales en matière d’électricité et de construction.
Die Geräte müssen von einem geprüften Elektriker entsprechend allen nationalen und lokalen Elektro – und Bauvorschriften in einem zugelassenen Gehäuse installiert werden.
Los dispositivos se deben instalar en un recinto aprobado por un electricista cualificado de acuerdo a todos los reglamentos eléctricos y de construcción locales y nacionales pertinentes
I dispositivi devono essere installati da un elettricista qualificato in un luogo approvato, in conformità a tutti gli standard e le norme nazionali e locali vigenti in materia di impianti elettrici e costruzioni edilizie.
Apparaten moeten door een erkende elektricien worden geïnstalleerd in een goedgekeurde behuizing in overeenstemming met alle nationale en lokale elektriciteits – en bouwvoorschriften en wetgeving.
デバイスを取り付ける際は、資格のある電気技師に依頼し、電気と建設に関する国および地域のすべての法令に従って、認可されている筐体内に取り付けてください。根据国家/地区及当地的电气与建筑规范和法规,该设备必须由有资质的电工安装在经批准的外罩内。
C
L N
NO NC C NO NC
CH1 CH2
M
C NO NC C NO NC
CH1 CH2
PLC
M
COM
CH1-CH2, CH3-CH4, CH5-CH6, CH7-CH8 ≤ 9.8 FLA (1/2 HP), 120 V
CH1-CH2, CH3-CH4, CH5-CH6, CH7-CH8 ≤ 8 FLA (1 HP), 240 V
DDRC810DT-GL ≤ 40 A
Output Ratings/Group
3 A 3 B
100-240 V0.25 A
+12
V
D +
D -
GN
DS
HLD
AU
X
N L CO
M
NO
NC
CH1
CO
M
NO
NC
CH2
CO
M
NO
NC
CH3
µP
CO
M
NO
NC
CH4
CO
M
NO
NC
CH5
CO
M
NO
NC
CH6
CO
M
NO
NC
CH7
CO
M
NO
NC
CH8
DyNet
SELV/Class 2
RS-485
RJ12
Dry
Co
nta
ct 3
Co
mm
on
Dry
Co
nta
ct 4
Co
mm
on
Dry
Co
nta
ct 1
Dry
Co
nta
ct 2
Dry
Co
nta
ct 6
Dry
Co
nta
ct 5
Co
mm
on
Co
mm
on
Dry
Co
nta
ct 7
Dry
Co
nta
ct 8
12 V 120 mADry Contact Inputs
4
IEC Overvoltage Category III
CN NOL NC C NO NC C NO NC C NO NC C NO NC C NO NC C NO NC C NO
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
NC
Output Ratings/Channel (CH)
General Use
Load Type
10 A, 240 V5 A, 24 V
5 A, 240 V X
X
X
X
X
1 A, 120 V0.5 A, 240 V
9.8 FLA (1/2 HP), 120 V8 FLA (1 HP), 240 V
100 A
Incandescent
TV-5, 120 V
5 A, 240 V5 A, 24 V
CH1-CH8 N/CCH1-CH8 N/O
TV Rating
Inrush Current
Electronic Ballast
Motor M
Output Ratings/Group
CH-CH ≤ 400 V
DDRC810DT-GL ≤ 40 A
≤ 5 mm2
10+ AWG0.62 Nm5.5 Lb-in
2
6 A 6 B
1 C 32 4C 5 C 6 7 C 8
1 C
< 20 m≤ 1.5 mm2
16+ AWG0.33 Nm3.0 Lb-in
5
≤ 2 A 0.4 Nm3.5v Lb-in
≤ 2.5 mm2
12+ AWG
SH
LD
D+
GN
D
D-
+12
V
AU
X
GND AUX
< 20 m
DyNetRS-485
RJ12 RJ12
Installation of a home and building automation and control system shall comply with HD 60364-4-41. The temperature limits and current-carrying capacities for the communication wires specified in HD 384.5.523 shall not be exceeded.
8
AZZ 378 0519 R16
© 2019 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.
www.lighting.philips.com/dynalite
DyNet RS-485
7