LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS

www.kenall.com | P: 800-4-Kenall | F: 262-891-9701 | 10200 55th Street Kenosha, Wisconsin 53144, USA This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.

1INSTALLATION INSTRUCTIONS

F-4260_091118

Luminaire for Parking GaragesTEKDEK™ LED

IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should

always be followed, including the following:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET

LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS.

DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT

CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE. SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS

INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS.

SAVE THESE INSTRUCTIONSSAFETY RECOMMENDATION

TD17 SERIES

SAFETY RECOMMENDATIONA 1/16" diameter aircraft cable with end-loop (not included) is recommended for attaching the �xture structural to the upper structural.

1/16" DIA. AIRCRAFT CABLE(SUPPLIED BY OTHERS)

AIRCRAFT CABLE ATTACHTO UPPER STRUCTURAL

SCREW (SUPPLIED BY OTHERS)

A 1/16" diameter cable with end-loop (not included) is recommended for attaching the fi xture structural to the upper structural



F-4260_091118

1: Remove tertiary lens (if provided) by unscrewing (4) captive screws.

2: Remove heatsinking/LED base by unscrewing (4) captive screws. These will be the inner most screws.

3: Disconnect the quick connector wires from the LED board and the driver.

4: Make electrical connection to J-box (for sizes, see next page). Circuit wire connection must be in J-box. Install housing to surface using (4) 5/16" diameter mounting holes.

5: Re-assemble by reversing the removal procedure.

DRIVERQUICK CONNECT HEATSINK/LED BASE

CAPTIVE SCREWS (4) FOR REMOVING HEATSINK

CAPTIVE SCREWS (4)

TERTIARY LENS (IF PROVIDED)

HOUSING

HOUSING TOP VIEW

5/16” MOUNTING HOLES (4)

DIRECT TO SURFACE INSTALLATION



F-4258_091118

QUICK MOUNT KIT INSTALLATION

1: Quick mount plate fastens to a secure J-box. Screws by others.

2: Align hanger bracket with center slot on top of fi xture as shown at right. Fixture can then hang from bracket while electrical connections are made.

3: After excess wires are in J-box (see sizes below), push the fi xture up to the mounting plate. Locking hooks should slide through slots. Twist fi xture until a “click” is felt or heard. Fixture is now in place.

LOCKING HOOKS

HANGER BRACKET QUICK MOUNT PLATE

1.

2. ALIGN HANGER BRACKETWITH CENTER SLOT

LOCKING HOOK SLOTS

3.

USED WITH THE FOLLOWING JUNCTION BOX SIZES:4" ROUND 4" SQUARE3-1/2" OCTAGON

3.37

3.37

2.50

2.50

4.773.50



F-4557_041013

BIRD GUARD INSTALLATION

1. Fasten tab through slots as shown above.

No tools required. Must install before fi xture is mounted.

2. Bird Guard lays inside of casting.

DIRECT TO SURFACE & QUICK MOUNT



F-4259_091118

PENDANT MOUNT INSTALLATION

1: Attach 3/4" threaded conduit to housing (provided by others).

2: Make electrical connections in conduit body (supplied by others).

CONDUIT BODY AND CONDUIT (BY OTHERS)

HOUSING TAPPED FOR 3/4” NPS THREAD

MUST USE SEALANT OR SEALING LOCKNUT

SWIVEL MOUNT NOT RECOMMENDED (Kenall does not supply counterbalance system)



F-4257_091118

TRUNNION KIT INSTALLATION

1: Attach housing plate to housing. Align notch. Use (4) fl at head screws (provided).

2: Assemble trunninon kits as shown using (4) ¼ -20 × .500" screws and nuts (provided).

3: Attach trunnion brackets to housing plate with (4) 10-32 × .375" hex head screws (provided).

4: Make electrical connections in conduit body (supplied by others). Attach ¾” NPT conduit hub (supplied by others) between conduit and J-box.

NOTE: Top of bracket to top of the fi xture measurements: 9.1" min; 14.6" max

TRUNNION BRACKETS

CONDUIT BODY AND CONDUIT (BY OTHERS)

HOUSING PLATE

HOUSING

(To increase depth, move this fastner here)

MUST USE SEALANT OR SEALING LOCKNUT

CONDUIT HUB(BY OTHERS)



F-4558_041013

Luminaire for Parking GaragesTEKDEK™ LED

1. Bird Guard lays on top of casting.

TD17 SERIESIMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including the following:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS.

DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.

SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS.

SAVE THESE INSTRUCTIONS

Pendant Mount

Trunnion Kit

BIRD GUARD INSTALLATION - PENDANT MOUNT & TRUNNION KIT

(For Trunnion Kit remove tabs)

2. Attach both sides with (4) screws provided.

NOTE: For LEL option, align hole in bird guard with LED indicator



F-4257_091118

MOUNT FIXTURE WITH REGARDS TO OPTICAL ALIGNMENT KEY DIRECTION

TYPES II, III, IV

TYPE V, NORMALTYPE V, SQUARE

TYPE II

TYPE III

TYPE IV

TYPE VNORMAL

TYPE VSQUARE

LIGHT DISTRIBUTION PATTERN TYPES

DRIVING LANE

DRIVING LANE

KEY OPTICALALIGNMENT KEY

For warranty information visit www.kenall.com/Resources/Certified-Performance-Warranties

For technical assistance, call 1-800-4KENALL (1-800-453-6255).

WARRANTY

CUSTOMER SERVICE



F-4257_041013

Documents

LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS