Service Manual 800 Tsm

TechnicalPublications

2146692100Revision 2

Senographe 700T and 800TsmService Manual

do not duplicate

Copyright 1997 by General Electric Co.

ATTENTIONLES APPAREILS RAYONS X SONT DANGEREUX LA FOIS POUR LE PATIENT ET POUR LE MANIPULATEUR

SI LES MESURES DE PROTECTION NE SONT PAS STRICTEMENT APPLIQUEESBien que cet appareil soit construit selon les normes de scurit les plus svres, la source de rayonnement X reprsente un dangerlorsque le manipulateur est non qualifi ou non averti. Une exposition excessive au rayonnement X entrane des dommages lorganisme.Par consquent, toutes les prcautions doivent tre prises pour viter que les personnes non autorises ou non qualifies utilisent cetappareil crant ainsi un danger pour les autres et pour ellesmmes.Avant chaque manipulation, les personnes qualifies et autorises se servir de cet appareil doivent se renseigner sur les mesures deprotection tablies par la Commission Internationale de la Protection Radiologique, Annales 26 : Recommandations de la CommissionInternationale sur la Protection Radiologique et les normes nationales en vigueur.

WARNINGXRAY EQUIPMENT IS DANGEROUS TO BOTH PATIENT AND OPERATOR

UNLESS MEASURES OF PROTECTION ARE STRICTLY OBSERVEDThough this equipment is built to the highest standards of electrical and mechanical safety, the useful xray beam becomes a source ofdanger in the hands of the unauthorized or unqualified operator. Excessive exposure to xradiation causes damage to human tissue.Therefore, adequate precautions must be taken to prevent unauthorized or unqualified persons from operating this equipment or exposingthemselves or others to its radiation.Before operation, persons qualified and authorized to operate this equipment should be familiar with the Recommendations of the Interna-tional Commission on Radiological Protection, contained in Annals Number 26 of the ICRP, and with applicable national standards.

ATENCIONLOS APARATOS DE RAYOS X SON PELIGROSOS PARA EL PACIENTE Y EL MANIPULADOR

CUANDO LAS NORMAS DE PROTECCION NO ESTAN OBSERVADASAunque este aparato est construido segn las normas de seguridad ms estrictas, la radiacin X constituye un peligro al ser manipuladopor personas no autorizadas o incompetentes. Una exposicin excesiva a la radiacin X puede causar daos al organismo.Por consiguiente, se debern tomar todas las precauciones necesarias para evitar que las personas incompetentes o no autorizadasutilicen este aparato, lo que sera un peligro para los dems y para s mismas.Antes de efectuar las manipulaciones, las personas habilitadas y competentes en el uso de este aparato, debern informarse sobre lasnormas de proteccin fijadas por la Comisin Internacional de la Proteccin Radiolgica, Anales No 26: Recomendacines de la Comi-sin Internacional sobre la Proteccin Radiolgica y normas nacionales.

ACHTUNGRNTGENAPPARATE SIND EINE GEFAHR FR PATIENTEN SOWIE BEDIENUNGSPERSONAL,WENN DIE GELTENDEN SICHERHEITSVORKEHRUNGEN NICHT GENAU BEACHTET WERDEN

Dieser Apparat entspricht in seiner Bauweise strengsten elektrischen und mechanischen Sichereitsnormen, doch in den Hnden unbe-fugter oder unqualifizierter Personen wird er zu einer Gefahrenquelle. bermige Rntgenbestrahlung ist fr den menschlichen Orga-nismus schdlich.Deswegen sind hinreichende Vorsichtsmanahmen erforderlich, um zu verhindern, daunbefugte oder unqualifizierte Personen solcheGerte bedienen oder sich selbst und andere Personen deren Bestrahlung aussetzen knnen.Vor Inbetriebnahme dieses Apparats sollte sich das qualifizierte und befugte Bedienungspersonal mit den geltenden Kriterien fr den ge-fahrlosen Strahleneinsatz durch sorgfltiges Studium des Hefts Nr. 26 der Internationalen Kommission fr Strahlenschutz (ICRP) vertrautmachen: Empfehlungen der Internationalen Kommission fr Strahlenschutz und anderer nationaler Normenbehrden.

GE Medical Systems Senographe 700T and 800TREV 2 sm 2146692100

i

TABLE OF CONTENTS

CHAPTER TITLE PAGE

LIST OF EFFECTIVE PAGES ix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 INSTALLATION 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 1 INTRODUCTION 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Chapter Overview 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Inspection for Damage 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 2 DESCRIPTION OF DELIVERED EQUIPMENT 11. . . . . . . . . . . . . . . . . . . . . . . . SECTION 3 HOW TO USE THE CONSOLE IN INSTALLATION MODE 11. . . . . . . . . . . . . . 31 Introduction 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Application vs. Installation 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Description of the Console 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Accessing the Generator and Gantry Installation Mode from the Console 14. . . . . . . . . 35 Installation Menu Tree Structure 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Accessing the Different Installation Menus in the Tree Structure 119. . . . . . . . . . . . . . . . 37 Saved Parameters and checksum 119. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Reloading of Default (Initial) Parameters 120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Returning to the Application Mode 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 Configuration Parameters 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3101 Gantry Present/Absent (PRS_A) 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3102 Type Selection (700T or 800T) 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3103 Display of Parameters Following an Exposure 122. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3104 Calendar and Clock 123. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3105 Visual Representation of Numerical Parameters 123. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3106 Visual Display of Parameter Values 124. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3107 Modification of a Parameter Value or Entry of a Measurement 124. . . . . . . . . . . . . . . . . . 3108 Entry of an AlphaNumeric Value 125. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 Principles of Generator Calibration 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3111 Vocabulary 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3112 Use of the First Trigger/Second Trigger Buttons During Installation 126. . . . . . . . . . . . . 3113 Inhibit Conditions Due to Gantry Absence 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3114 Inhibit Conditions Due to Grid Absence/Presence 127. . . . . . . . . . . . . . . . . . . . . . . . . . . .


ii

TABLE OF CONTENTS (CONT.)

CHAPTER TITLE PAGE

3115 Displayed Messages During ExposureProducing Calibration Procedures 127. . . . . . . . . 3116 Other Displayed Messages 127. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 4 site preparation 127. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 5 installation steering 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 6 INSTALLATION job cards 135. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card IST 001 137. . . . . . . . . Job Card IST 002

139. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card IST 003

143. . . . . . . . . . . . . . . . . . Job Card IST 004 147. . . . . . . . . . . . . . . . . . . . . . . . Job Card IST 005

153. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card IST 006 159. . . . . . . . . . . Job Card IST 007 163. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card IST 008 165. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card IST 009 171. . . . . . . . . . . . . . . . . Job Card IST 010 )'!*,( '&!#"+(*#'& 177. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card IST 011 &)*$$*#'& '(% 181. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 CENTRAL LISTING 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 CALIBRATION 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 1 INTRODUCTION 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 2 SENOGRAPHE TYPE 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 3 GENERATOR CALIBRATION 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 4 GANTRY CALIBRATION 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 5 CALIBRATION JOB CARDS 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card CAL 001 35. . . Job Card CAL 002

311. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card CAL 003 317. . . . . Job Card CAL 004

321. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card CAL 005

325. . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card CAL 006

329. . . . . . . Job Card CAL 007

333. . . . . . . . . . . . . . . . . . . . . . . . . . . . .


iii


CHAPTER TITLE PAGE

Job Card CAL 008 351. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Job Card CAL 009 355. Job Card CAL 010

359. . . . . . . . . . . . . . . . . . Job Card CAL 011 361. . . . . . . . . . Job Card CAL 012 365. . . Job Card CAL 013

369. . Job Card CAL 014

379. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card CAL 015 385Job Card CAL 016

389. . . . Job Card CAL 017 393. . . . . . . . . . . . . . . . . . . Job Card CAL 018 397. Job Card CAL 019 3101. . . . Job Card CAL 020

3105. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card CAL 021 3111. . . . . . . . . . . Job Card CAL 022

3125. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card CAL 023 3129. . . . . . . . Job Card CAL 024 3137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card CAL 025 CHECK & ADJUSTMENT OF CENTERING DEVICE LAMP 3143. . . . . Job Card CAL 026 CHECK & ADJUSTMENT OF ELEVATOR SAFETY SWITCH 3149. . . .

4 DISASSEMBLY/RE-ASSEMBLY 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 1 DISASSEMBLY/RE-ASSEMBLY JOB CARDS 41. . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 001 ! 43. . Job Card DR 002 !

45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 003 ! 49. . . . . . . Job Card DR 004 !

! 413. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 005 ! 417. . Job Card DR 006 !

! 421. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 007

425. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


iv


CHAPTER TITLE PAGE

Job Card DR 008 ! "! 431. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Job Card DR 009 ! "! 435. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Job Card DR 010 ! "! ! 441. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Job Card DR 011 " 443. . . . . . Job Card DR 012 ! "!

! 447. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 013 ! "! "! 451. . . . Job Card DR 014 ! "! 455Job Card DR 015 ! "!

! 459. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 016 ! !

461. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 017 "

463. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 018 ! "!

! 467. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 019 ! "!

" 471. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 020 ! "!

! 473. . . . . . . . . . . . . . . Job Card DR 021 ! "!

477. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 022 ! "!

! 481. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 023 DISASSEMBLY & REASSEMBLY OF THE MAGNIFICATION

BOARD 200PL6 485. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 024 ! "! ! 487. . . Job Card DR 025

491. . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 026 ! "! 493. . . . . . . . . . . Job Card DR 027 495. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 028 ! "!

499. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 029 ! "! !

4103. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Card DR 030 ! "!

4105. . . . . . . . . . . . . . Job Card DR 031 ! "!

4109. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


v


CHAPTER TITLE PAGE

Job Card DR 032 4113. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Job Card DR 033 4117. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 RENEWAL PARTS 5i. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 SIGNAL NAME 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 ERROR LIST 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 1 ERROR CODE STRUCTURE 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


vi

Blank page.


vii

THIS SERVICE MANUAL IS AVAILABLE IN ENGLISH ONLY.

IF A CUSTOMERS SERVICE PROVIDER REQUIRES A LANGUAGE OTHER THANENGLISH, IT IS THE CUSTOMERS RESPONSIBILITY TO PROVIDE TRANSLATIONSERVICES.

DO NOT ATTEMPT TO SERVICE THE EQUIPMENT UNLESS THIS SERVICEMANUAL HAS BEEN CONSULTED AND IS UNDERSTOOD.

FAILURE TO HEED THIS WARNING MAY RESULT IN INJURY TO THE SERVICEPROVIDER, OPERATOR OR PATIENT FROM ELECTRIC SHOCK, MECHANICALOR OTHER HAZARDS.

CE MANUEL DE MAINTENANCE NEST DISPONIBLE QUEN ANGLAIS. SI LE TECHNICIEN DU CLIENT A BESOIN DE CE MANUEL DANS UNE AUTRE

LANGUE QUE LANGLAIS, CEST AU CLIENT QUIL INCOMBE DE LE FAIRETRADUIRE.

NE PAS TENTER DINTERVENTION SUR LES QUIPEMENTS TANT QUE LEMANUEL SERVICE NA PAS T CONSULT ET COMPRIS.

LE NON-RESPECT DE CET AVERTISSEMENT PEUT ENTRANER CHEZ LETECHNICIEN, LOPRATEUR OU LE PATIENT DES BLESSURES DUES DESDANGERS LECTRIQUES, MCANIQUES OU AUTRES.

DIESES KUNDENDIENSTHANDBUCH EXISTIERT NUR INENGLISCHER SPRACHE.

FALLS EIN FREMDER KUNDENDIENST EINE ANDERE SPRACHE BENTIGT, ISTES AUFGABE DES KUNDEN FR EINE ENTSPRECHENDE BERSETZUNG ZUSORGEN.

VERSUCHEN SIE NICHT, DAS GERT ZU REPARIEREN, BEVOR DIESESKUNDENDIENSTHANDBUCH NICHT ZU RATE GEZOGEN UND VERSTANDENWURDE.

WIRD DIESE WARNUNG NICHT BEACHTET, SO KANN ES ZU VERLETZUNGENDES KUNDENDIENSTTECHNIKERS, DES BEDIENERS ODER DES PATIENTENDURCH ELEKTRISCHE SCHLGE, MECHANISCHE ODER SONSTIGE GEFAHRENKOMMEN.

ESTE MANUAL DE SERVICIO SLO EXISTE EN INGLS. SI ALGN PROVEEDOR DE SERVICIOS AJENO A GEMS SOLICITA UN IDIOMA

QUE NO SEA EL INGLS, ES RESPONSABILIDAD DEL CLIENTE OFRECER UNSERVICIO DE TRADUCCIN.

NO SE DEBER DAR SERVICIO TCNICO AL EQUIPO, SIN HABER CONSULTADO YCOMPRENDIDO ESTE MANUAL DE SERVICIO.

LA NO OBSERVANCIA DEL PRESENTE AVISO PUEDE DAR LUGAR A QUE ELPROVEEDOR DE SERVICIOS, EL OPERADOR O EL PACIENTE SUFRAN LESIONESPROVOCADAS POR CAUSAS ELCTRICAS, MECNICAS O DE OTRANATURALEZA.

WARNING

AVERTISSEMENT

WARNUNG

AVISO


viii

ESTE MANUAL DE ASSISTNCIA TCNICA S SE ENCONTRADISPONVEL EM INGLS.

SE QUALQUER OUTRO SERVIO DE ASSISTNCIA TCNICA, QUE NO A GEMS,SOLICITAR ESTES MANUAIS NOUTRO IDIOMA, DA RESPONSABILIDADE DOCLIENTE FORNECER OS SERVIOS DE TRADUO.

NO TENTE REPARAR O EQUIPAMENTO SEM TER CONSULTADO ECOMPREENDIDO ESTE MANUAL DE ASSISTNCIA TCNICA.

O NO CUMPRIMENTO DESTE AVISO PODE POR EM PERIGO A SEGURANA DOTCNICO, OPERADOR OU PACIENTE DEVIDO A CHOQUES ELTRICOS,MECNICOS OU OUTROS.

IL PRESENTE MANUALE DI MANUTENZIONE DISPONIBILESOLTANTO IN INGLESE.

SE UN ADDETTO ALLA MANUTENZIONE ESTERNO ALLA GEMS RICHIEDE ILMANUALE IN UNA LINGUA DIVERSA, IL CLIENTE TENUTO A PROVVEDEREDIRETTAMENTE ALLA TRADUZIONE.

SI PROCEDA ALLA MANUTENZIONE DELLAPPARECCHIATURA SOLO DOPO AVERCONSULTATO IL PRESENTE MANUALE ED AVERNE COMPRESO IL CONTENUTO.

NON TENERE CONTO DELLA PRESENTE AVVERTENZA POTREBBE FARCOMPIERE OPERAZIONI DA CUI DERIVINO LESIONI ALLADDETTO ALLAMANUTENZIONE, ALLUTILIZZATORE ED AL PAZIENTE PER FOLGORAZIONEELETTRICA, PER URTI MECCANICI OD ALTRI RISCHI.

ATENO

AVVERTENZA


ix

REVISION HISTORY

REV DATE REASON FOR CHANGE

0 Mar. 12, 1996 Initial release

1 April 24, 1996 Update.

2 Jan 17, 1997 Update.

LIST OF EFFECTIVE PAGES

PAGENUMBER

REVISIONNUMBER

PAGENUMBER

REVISIONNUMBER

PAGENUMBER

REVISIONNUMBER

Title pageSafety Instruction

22

i thru x 2

11 thru 194 2

21 thru 218 2

31 thru 3152 2

41 thru 4118 2

5i thru 5ii51 thru 564

22

61 thru 624 2

71 thru 714 2


x

Blank page.

INST

ALL

ATIO

N


11

CHAPTER 1 INSTALLATION

SECTION 1INTRODUCTION

11 Chapter Overview

This chapter presents the Senographe installation procedures. The wiring and room layoutrequirements for the product are covered in the PreInstallation Manual.

12 Inspection for Damage

The Senographe was completely inspected for proper operation and appearance beforeshipment. However, it is necessary to inspect the product after the shipment is received.Visually inspect the packages for any apparent damage. If there are signs of damage, refer tothe Damage in Transportation statement in the front of this manual.

Open the packages and refer to the Product Delivery Instructions (PDI). Verify that items onthe list are present in the package. Carefully examine the contents for small parts.

SECTION 2DESCRIPTION OF DELIVERED EQUIPMENT

See PreInstallation Manual for description of delivered equipment.

SECTION 3HOW TO USE THE CONSOLE IN INSTALLATION MODE

31 Introduction

This section describes how to use the Senographe console during product installation.

32 Application vs. Installation

Throughout the Senographe documentation, reference is made to the application mode, asopposed to the installation mode, in order to differentiate between normal operation of theproduct by a doctor and operation of the product during installation.

Each time the Senographe is turned on, the software automatically starts up in theapplication mode.

For information on using the Senographe in application mode, see Operator Manual.

One Senographe assembly must be installed. Therefore, there are two separate installationmodes, one for the generator and one for the gantry. See Section 34.

INST

ALL

ATIO

N


12

33 Description of the Console

Illustration 11 shows the console. When the Senographe is in application mode, containskeys below the display window correspond to the functions that their respective symbolmarkings. See Operator Manual.

On the other hand, when the Senographe is in installation mode, the function of each of thesesix keys depends on the procedure being performed and is displayed on the bottom line of thedisplay window, adjacent to the corresponding key.

To enter installation mode, press the SETUP key once. To return immediately to

application mode, press the SETUP key again.

Illustration 12 shows the console before and after entry into the installation mode. Section 1of this illustration shows a typical console display during normal application mode use.Section 2 shows the appearance of the display window after, starting from application mode,

the SETUP key is pressed once.

ILLUSTRATION 11SENOGRAPHE CONSOLE

INST

ALL

ATIO

N


13

ILLUSTRATION 12

CONSOLE DISPLAY BEFORE (1) AND AFTER (2) SETUP KEY IS PRESSED ONCE STARTING FROM APPLICATION MODE

MEDICAL

SMALL

APPLICATION

SETUP

APPLICATION

SETUP

MEDICAL INSTAL

2

1

(Selection with 800T only)

GEMS PEOVO.2 16.06.95INSTAL MAINT PASSWD

Mo Mo

INST

ALL

ATIO

N


14

34 Accessing the Generator and Gantry Installation Mode from the Console

Menu access paths: SETUP/INSTAL/GENE OR SETUP/INSTAL/ARM

To access the generator and gantry installation mode starting from application mode, followthis sequence:

1. Press the SETUP key .

2. The MAINT menu is not accessible with the console.

3. Change the position of the installation menu enable switch (switch 8 of B1 on CPU board300PL4) from its position prior to powerup to the opposite position. See Illustration 13.This enables access to the generator and gantry installation menus.

Note: To access to the installation menu you can also select the PASSWD key and compose thepassword (given at the training course). And press the SETUP key.

4. Select the INSTAL menu.

5. You now have access to the installation menus.

Note: The position of the installation menu enable switch or PASSWD key is memorized eachtime the Senographe is turned on. Until the machine is again turned off (or the defaultparameters are reloaded via the INSTAL CLEAR menu, see Section 38), thismemorized position will be the installation menu access disabled position, and theopposite position will be the installation menu access enabled position. The significanceof the switchs position at a given moment thus depends upon its position at powerup.

When you have finished using the Senographe installation mode, you must turnoff the Senographe before turning over use of the machine to the user. In this way,when the machine is turned on again, access to the installation mode will beautomatically locked out. See Note above.

Illustration 14 shows the sequence for accessing installation mode.

CAUTIONCAUTION

INST

ALL

ATIO

N


15

ILLUSTRATION 13LOCATION OF INSTALLATION MENU ENABLE SWITCH

CPU BOARD 300PL4

P2P1

B1 ?

8 1

INST

ALL

ATIO

N


16

ILLUSTRATION 14SEQUENCE FOR ENTERING INSTALLATION MODE

2

1

SMALL

APPLICATION

SETUP

(Selection with 800T only)

CPU BOARD 300PL4

P2P1

B1 ?

8 1

Mo Mo

INST

ALL

ATIO

N


17

ILLUSTRATION 15

3

4

MEDICAL

APPLICATION

SETUP

MEDICAL INSTALGEMS PEOVO.2 16.06.95INSTAL MAINT PASSWD

CONFIG

LAST INSTAL (D/M/Y H:M) 16.06.95 22:15

APPLICATION

SETUP

MEDICAL INSTAL

CKSUM

CONFIG ARMAOPGENECKSUM

GENE AOP ARM

INST

ALL

ATIO

N


18

35 Installation Menu Tree Structure

The various installation menus are accessible via a tree structure. Illustrations 16 to 115show this tree structure.

INST

ALL

ATIO

N


19

ILLUSTRATION 16INSTALLATION MENU TREE STRUCTURE

NEXT

APPLICATION MODE THE SENOGRAPHE 700T & 800T MENUKEY

indicates that rotation of the kV knob will either displayother parameter values, or modify a digit or character ina string being entered.

indicates that the 2nd trigger button must be pressed inorder to perform the calibration (see associatedinstructions for the calibration in question before usingthese menus).

indicates that several values can be displayed byrotating the kV knob.

(values)

(value) indicates that a single value is displayed or can bemodified or entered.

GEMSE PEO_VX.Y 16.06.95MEDICAL INSTAL MAINT PASSWD 00001

ENTER YOUR PASSWORD: .............1 2 3 4 5 6 00004

LAST CALIB (D/M/Y H:M) (date) (time)CKSUM CONFIG GENE AOP ARM MFG 00002

KAUTOMATIC EXPOSURE AOP

CELL ALGO COPY PADDLE TYPE 000132(status arm)

G H I JSTATUS: AOP X

A B C 00777CHECKSUM OF SAVED PARAM

CKSUM CLEAR 00021

CHECKSUM DONE00022

SYSTEM CONFIGURATIONTYPE CONFIG DISP DATE PRS_A 00020

SENO TYPE: (type)700T 800T 00037

GENERATOR CONFIGURATIONTUBE PMAX MASMAX T_MAX 1 > 2 00024

GENERATOR CALIBRATIONTUBE HTR_SCL BIAS kV mA_meas 00114

B C

E

F

EXPOSURE PARAM DISPLAY (YES/NO)YES NO 00034

DATE and TIME UPDATEDAY HOUR 00031

00033

TYPE OF TUBE (2Foc/met/2ang)FOCUS ANODE 00025

MAX AUTHORIZED POWER POWE=(value)3.0 kW 3.5 kW 4.0 kW 4.5 kW 5.0 kW 00111

MAX mAs ALLOWED mAs=(value)NEXT VALID 00035

MAX EPOSURE TIME T (s)=(value)NEXT VALID 00036

TIME HH:MM:SS (time)VALID 00032

GENERATOR CONFIGURATIONRINIT 2 > 1 00113

RE_INITIALISATIONINIT_TUBE 00112

TUBE REINITIALISATIONVALID 00130

Menu 00024

ARM PRESENCE (YES/NO)YES NO 00026

A

D

CLEAR ALL SAVED PARAMVALID 00023

DATE DD/MM/YY (date)NEXT VALID 00033

See ILL. 17

See ILL. 114

See ILL. 110 See ILL. 110See ILL. 111 See ILL. 111

See ILL. 18 See ILL. 18

See ILL. 19

See ILL. 19

See ILL. 19

MANUFACTURINGENDUR 00009

INST

ALL

ATIO

N


110

ILLUSTRATION 17INSTALLATION MENU TREE STRUCTURE (contd)

KEY




(values)


MEDICAL

MEDICAL SETUPSPEED FORCE DECOMP HEIGHT AOP 1 > 2 05100

A

COMPRESSION SPEED: (selected speed)FAST SLOW 05101

MAX COMPRESS FORCE: (value) daN+ _ VALID 05107

END OF EXPOSURE DECOMP: (YES/NO)YES NO 05103

MEDICAL SETUPLANG FILM 2 > 1 05110

CASSETTE DETECTION: (YES/NO)YES NO 00110

DECOMPRESSION HEIGHT: (value) cm+ _ VALID 05102

SELECT LANGUAGE (selecd language)FRANC ENGL DEUTS ESPAN ITALI PORTUG 05108

MAX. DROP IN OD FOR (AE): (value)+ _ FSC 00341

Menu 05100

SREEN/FILM PAIR CHOISE FSC=(AE)CHOICE 00343

From ILL. 16

INST

ALL

ATIO

N


111


KEY




(values)


INSTALL/GENETUBE

HTR_SCL

B

TUBE CALIBRATIONHEATER HTR_D CTUBE CTubH WarmUp 00115

HEATER: Select Foc/TrackLF/MO SF/MO LF/RH SF/RH 00117

HEATER: LF/MO CALIBCALIB PARAM 00118

HEATER: LF/MO CALIBC_GAIN I_VALUE 00156

HTR_SCL HARDWARE TRACK1CALIB PARAM 00125

CHTR_SCL HADWARE CALIB

TRACK1 TRACK2 00124

HTR DELTA ParametersLF/MO SF/MO LF/RH SF/RH 00121

HEATER: LF/MO CALIB00119

Cathode Gain LF/Mo GK_Ax=(values)CHANGE 00148

Modif LF/Mo cathode gain GK_Ax=(value)NEXT VALID 00149

Currents LF/MO (values) kV (values) ACHANGE 00174

Currents LF/MO (value)kV (value) ANEXT VALID 00120

TUBE WARMUP x/ykV00387

CtubH PARAM display Cbmax=(values)CHANGE 00123

LF/Mo HTR_DELTA display DEL_x=(values)00163

CTubH PARAM modif Cbmax=(value)NEXT VALID 00165

Same menustructure asfor LF/MO

Same menustructure asfor LF/MO

Same menustructure asfor TRACK1

PARAM HTR_SCL: track 1 X=(values)CHANGE 00126

PARAM HTR_SCL: modif track 1 x(value)NEXT VALID 00249

HTR_SCL HARDWARE TRACK11 st pt 2 nd pt CALCUL 00251

Same menustructure asfor 1 st pt

HTR_SCL HARDWARE TRACK1 ref=(value)CMDE CALIB Measl 00224

NEXTHTR_SCL TRACK1 PT1 modif ref=(value)

VALID 00250

00145HTR_SCL CALIB TRACK1 PT1 ref=(value)

NEXTHTR_SCL TRACK1 1 st point meas=(value)

VALID 00247

TRACK K1 HTRSCL calculVALID 00248

From ILL. 16

From ILL. 16

INST

ALL

ATIO

N


112


kV CALIBRATIONCALIB PARAM 00369

KEY




(values)


INSTAL/GENEBIASkV

FOCAL BIAS VOLTAGECALIB PARAM VOLT. RESIT 00127

FOCAL BIAS VOLTAGE CALIB1st pt 2 nd pt CALCUL 00128

FOCAL BIAS VOLT display (alpha/beta)=(values)CHANGE 00129

FOCAL BIAS VOLT 1 st ptCALIB MeasV 00166

D

BIAS RESISTOR VALUE Res=(value)NEXT VALID 00388

FOCAL BIAS VOLTAGE DISP. (1st/2nd) (values)00243

E

kV PARAMETERS (G/VOF)CHANGE 00380

PARAM kV modif x=(value)NEXT VALID 00381

kV CALIBRATION1 st pt 2 nd pt calcul 00370


kV CALIB 1 st point ref=(value)REF CALIB kV_M 00371

kV REFERENCE 1 st point ref=(value) kVNEXT VALID 00372

FOCAL BIAS VOLT measure meas=(value)NEXT VALID 00245

FOCAL BIAS VOLT 1st pt ref=(value)00215

KV CALIB 1st point00373

MEASURE kV 1 st meas=(value)NEXT VALID 00374

FOCAL BIAS VOLT modif x=(value)NEXT VALID 00131

FOCAL BIAS VOLT calculVALID 00263


kV CALIB: calculVALID 00379

mA MEASUREMENTCALIB PARAM 00116

F

mA MEASURE CALIBRATIONCALIB I_MEAS CALCUL 00363

MEASURED CURRENT meas=(value)NEXT VALID 00366

mA MEASURE CALIBRATION meas=x mAMEASUR 00365

mA MEASUREMENT PARAM f/mA=(value)CHANGE 00364

mA MEAS PARAM MODIF f/mA=(value)NEXT VALID 00368

mA_meas

mA MEASUREMENT CALCVALID 00367

From ILL. 16

From ILL. 16

From ILL. 16

INST

ALL

ATIO

N


113


KEY




(values)


INSTAL/AOPCELL

COPYCELL CALIBRATION (status arm)HV/DAC PM/HV GAIN 00133

G

PM_HV/DAC CALIBRATION (status arm)FREQ/HV HV/DAC CHECK 00134

FREQUENCY/PM_HV GAIN (status arm)CALIB PARAM 00168

PM/PM_HV calibration (status arm)CALIB PARAM 00137

PM/PM_HV PARAM display (apha/beta/gamma)=(values)CHANGE 00139

PM/PM_HV PARAM change x=(value)NEXT VALID 00170

PM_HV/DAC CALIBRATION (status arm)CALIB PARAM 00260

PARAMETERS DUPLICATION x > ySOURCE TARG COPY 00264

I

ENABLE COPYVALID 00267

TARGET CHOISESCREEN FSC 00266

TARGET FSC CHOISE FSC=(fsc)FSC=A FSC=B FSC=C FSC=D FSC=E 00271

SCREEN PRESENT (YES/NO)YES NO 00270

SOURCE CHOISE (x)SCREEN FSC 00265

TARGET FSC CHOISE FSC=(x)FSC=A FSC=B FSC=C FSC=D FSC=E 00269


FREQ/PM_HV GAIN display F/HV=(value)CHANGE 00258

FREQ/PM_HV GAIN change F/HV=(value)NEXT VALID 00259

FREQUENCY/PM_HV GAIN ref=(value)REF CALIB HV_M CALC 00256

PM/PM_HV Calibration

PM_HV/DAC PARAM display (alpha/beta)=(values)CHANGE 00136

PM_HV/DAC PARAM change x=(value)NEXT VALID 00169

CHECK HV CALIBRATIONREF TEST 00147

High voltage tead [v]: (value)00149

High voltage wanted [v]: HV=(value)CHANGE 00151

High voltage wanted [v]: HV=(value)NEXT VALID 00152

PM GAIN display Gain=+1.000E+0CHANGE 00159

PM GAIN change Gain=+1.000E+0NEXT VALID 00148

FREQ/PM_HV REF modif (ref=(value)NEXT VALID 00257

Send PM/HV refSTART STOP 00261

PM_HV/DAC PARAM calibrationSTART 00135

FREQ/PM_HV CALCUL (/calcul done)VALID 00217

FREQ/PM_HV GAIN measure meas=(value)NEXT VALID 00262

00138

From ILL. 16

From ILL. 16

INST

ALL

ATIO

N


114


KEY




(values)


INSTAL/AOPALGO

PADDLEAEC/AOP CALIBRATION (status arm)

FSC=A FSC=B FSC=C FSC=D FSC=E 00144

H

Same menu structureas for FSC=ASame numbers

AEC/AOP CALIBRATION FSCA=XVALID NAME TYPE STRAT CALIB 00176

FSC validation (YES/NO)YES NO 00178

SCREEN/FILM STRATEGY (strategy)MEDIUM SLOW FAST V_SLOW V_FAST S_FAST 00177

PADDLE CHOISE18X24 24X30 Magn. 00338

J

PADDLE PARAMETERS (status arm or (xxy))PARAM 00388

Select FSC Type1SCR 2SCR NSCR 00180

Select FSC Name FSC X=(name)NEXT VALID 00179

Same menustructure asfor 18x24

PADDLE PARAM display x=(values)CHANGE 00389

PADDLE PARAM CHANGE x=(value)NEXT VALID 00390

ALGORITHM CALIBRATION (status arm) or (FSCX=name)PM_yld LNRT Energ 00181

REFERENCE ENERGY FSCX=(name)CALIB PARAM CONFIG 00197

N

CALIBRATION WITH GRID (YES/NO)YES NO 00194

MPM YIELD (FSCX/(m)GRID/(n)SCR

SCREEN GRID CALIB 00182


L

REFENERGY CALIBRATION mAs=(value)mAs CALIB OD_MS CALC 00203

REFENERGY CALIBRATION

mAs Selection mAs=(value)NEXT VALID 00204

REFENERGY calcVALID

Measured density OD=(value)NEXT VALID 00206

See ILL. 113

See ILL. 112 See ILL. 112

00205

From ILL. 16

From ILL. 16

INST

ALL

ATIO

N


115


FILM/SCREEN CALIBRATION FSCX/GRID/SCRCALIB PARAM 00184

N

L

KEY




(values)


FSC PARAM display Trac x/filtyCONFIG PARAM 00191

FSC PARAM display FT AX=(values)CHANGE 00189

FILM/SCREEN PARAM change AX=(value)NEXT VALID 00190

Select Configuration (track/filt)Mo/Mo Mo/Rh Mo/A1 Rh/A1 Rh/Rh 00192

FILM/SCREEN CALIBRATION (status arm)THICK CALIB CALC 00185

FILM/SCREEN CALIBRATIONVALID

Select plexi thickness x cm2 cm 4 cm 6 cm 00186

INSTAL/AOPALGO

PADDLE

REF_ENERGY PARAM menu FSCX=(name)GAMMA ENR_R OD_R SCALE D_STEP 00200

REFERENCE ENERGY display STEP=(value)CHANGE 00201

REFERENCE ENERGY change STEP=(value)NEXT VALID 00202

REFERENCE ENERGY display OD_X=(values)CHANGE 00201

REFERENCE ENERGY change OD_X=(value)NEXT VALID 00202

REFERENCE ENERGY display od_r=(value)CHANGE 00201

REFERENCE ENERGY change OD_r=(value)NEXT VALID 00202

REFERENCE ENERGY display ENERG=(value)CHANGE 00201

REFERENCE ENERGY change ENERG=(value)NEXT VALID 00202

REFERENCE ENERGY display GAMMA=(value)CHANGE 00201

REFERENCE ENERGY change GAMMA=(value)NEXT VALID 00202

PARAMETERS CalculationVALID 00188

00187

From ILL. 111

From ILL. 111

INST

ALL

ATIO

N


116


KEY




(values)


INSTAL/AOP/ALGO/FSC=x/CALIBLNRT

CORR(TIME RECIP. FAIL)

MAG.HEATER REFEN LNRT PARAM 00193

M

LNRT PARAM display FSC=X AY=(values)CHANGE 00195

LNRT PARAM change FSC=X AY=(value)NEXT VALID 00196

TIME RECIPROLITY FAILURE THICK. = xcmCALIB OD_mea CALC 00334

MEASURED OPTICAL DENSITY=(value)NEXT VALID 00349

TIME RECIPROCITY FAILURE00348

CALIB REF_ENERGY OF LNRT mAs=(value)CALIB OD_mea CALC 00343

HEATER CALIBRATION (status arm)CALIB PARAM 00335

MEASURED DENSITY OD=(value)NEXT VALID 00346

CALIB REF_ENERGY OF LNRT00345

HEATER CALIBRATION00338

CALIB REF_ENERGY OF LNRT (status arm)OD_ref SCALE mAs CALIB 00339

REF ENERGY PARAM DISPLAY OD_X=(values)CHANGE 00340

REF ENERGY PARAM MODIF OD_X=(value)NEXT VALID 00344

REF ENERGY PARAM DISPLAY OD_r=(value)CHANGE 00340

REF ENERGY PARAM MODIF OD_r=(value)NEXT VALID 00344

REF ENERGY PARAM DISPLAY mAs=(value)CHANGE 00340

REF ENERGY PARAM MODIF OD_X=(value)NEXT VALID 00344

HEATER PARAM DISPLAY kV=(values) I=(values)CHANGE 00336

HEATER PARAM MODIF kV=(value) I=(value)NEXT VALID 00337

TIME RECIPROCITY FAILURE (value sec)00348

RECIPROCITY FAIL.: calcVALID 00350

CALIB REF_ENERGY calcVALID 00347

From ILL. 111

THICK

THICKNESS PLEXI FSCX = (name) 1.5 cm 2 cm 6 cm

THICKNESS PLEXI

THICKNESS PLEXI

THICKNESS PLEXI

TIME RECIPROCITY FAILURE (status arm) or(FSCX=(name))

00194

00366

00366

00366

INST

ALL

ATIO

N


117


KEY




(values)


INSTAL/ARMKCOMP THICK ANGLE 05250

BREAST THICKNESS CALIBPOTENT. PARAM CONTACT MAGNIF 05251

COMPRESSION CALIBRATIONFORCE LIMIT 05270

MAGNIF MODE THICKNESSCALIB PARAM 05257

MAGNIF. MODE THICK PARAMOFFEST ELASTIC 05254

MAGNIF THICK ELASTIC=(value)NEXT VALID 05256

MAGNIF THICK OFFEST=(value)NEXT VALID 05255

MAGNIF MODE THICK CALIB15daN (Calcul)

CONTACT MODE THICKNESSCALIB PARAM 05257

CONTACT MODE THICK PARAMOFFSET ELASTIC 05254

CONTACT THICK ELASTIC=(value)NEXT VALID 05256

CONTACT THICK OFFSET=(value)NEXT VALID 05260

CONTACT MODE THICK CALIB15daN (Calcul)

THICK DETECTOR PARAMETERMEASURE CALCUL 05262

THICK PARAMETER Xcm=(values)CHANGE 05263

PARAM THICK modif Xcm=(valu)NEXT VALID 05264

COMP CURRENT LIMIT CALIBLIM_IC LIMIT_OC 05277

LIMIT (value)%+ VALID 05280

LIMIT (value)%+ VALID 05279

FORCE DETECTOR CALIBCALIB PARAM 05271

FORCE DETECTOR PARAMETERMEASURE CALCUL 05284

FORCE PARAMETER Xbg=(values)CHANGE 05285

PARAM FORCE modif Xbg=(value)NEXT VALID 05286

FORCE DETECTOR CALIBMEASURE CALCUL 05272

FORCE DETECTOR MEASURES 13 daN 0 daN 3 daN 6 daN 1 > 2 05281

FORCE DETECTOR MEASURES 29 daN 12 daN 15 daN 18 daN 2 > 3 05282

FORCE DETECTOR MEASURE 321 daN 24 daN 27 daN 3 > 1 05283

PSee ILL. 115

Menu 05281

From ILL. 16

INST

ALL

ATIO

N


118


INSTAL/ARM/ANGLE

P

ANGLE DETECTOR CALIBCALIB PARAM 05290

ANGLE DETECTOR PARAMETERMEASURE CALCUL 05295

ANGLE PARAMETERS xd=(values)CHANGE 05296

PARAM ANGLE modif X=(value)NEXT VALID 05297

ANGLE DETECTOR CALIBMEASURE CALCUL 05291

ANGLE DETECTOR MEASURES 1180 135 90 1 > 2 05292

ANGLE DETECTOR MEASURES 245 0 45 2 > 3 05293

ANGLE DETECTOR MEASURE 390 135 (degree) 3 > 1 05294

KEY




(values)


Menu 05292

From ILL. 114

INST

ALL

ATIO

N


119

36 Accessing the Different Installation Menus in the Tree Structure

Once you have followed the installation mode access procedure given in Section 34, you cango down into the various installation menus by selecting them progressively using the six keysbelow the console display window. See Section 35.

To move upward in the tree structure, press the SETUP key one time for each level

desired. This is useful for going from one branch of the tree structure to another duringinstallation procedures, or if you accidentally go into an unwanted branch.

37 Saved Parameters and checksum

a. Parameters resulting from installation or nonproprietary maintenance proceduresare saved in a memory zone whose contents are not lost when the Senographe isswitched off.

b. To perform a saved parameter memory checksum, go to the CKSUM menu and runthis function. You can now return to application mode without receiving aCHECKSUM ERROR message.

c. It is not mandatory to do a checksum each time you leave a menu. There is no riskof losing data if you switch off the Senographe displaying checksum error.

The only purpose of checksum error is to lock the application mode against anyrandom data change. When you perform the checksum you only tell the software thatyou accept the data you change before (entered normally or calibrated).

INST

ALL

ATIO

N


120

38 Reloading of Default (Initial) Parameters

THE FUNCTIONS DESCRIBED IN THIS SECTION ARE NORMALLYNEVER USED AFTER THE SENOGRAPHE HAS LEFT THE FACTORY.

To reload the default parameters (prior to any installation or calibration procedures), use therespective CLEAR menu. The use of this menu executes a software powerupcomparable to the very first hardware powerup.

When the INSTAL CLEAR menu is used, the Senographe leaves the installation menus andreturns to the application mode. In order to reaccess the installation mode after performing aINSTAL CLEAR, you must change the position of the installation menu enable switch. SeeSection 34, or use the PASSWD key.

Following use of the CLEAR menu, the software displays a CHECKSUM ERRORmessage. All generator or gantry calibration procedures must be performed, followed by aCKSUM in order to enable use of the new parameters.

USE OF THE INSTAL CLEAR MENU RESETS, FROM A SOFTWAREPOINT OF VIEW, THE THERMAL CONDITION OF CRITICALCOMPONENTS (TUBE, TUBE HOUSING, GENERATOR, ETC.) TO ACOLD CONDITION. THIS MEANS THAT THE SOFTWARE THERMALPROTECTIONS CAN NO LONGER DETECT AN EXCESSIVETEMPERATURE IMMEDIATELY FOLLOWING USE OF THIS MENU.

THE INSTAL CLEAR MENU MUST THEREFORE BE USED WITHCARE, ESPECIALLY WHEN OPERATIONS JUST PRIOR TO ITS USEHAVE SIGNIFICANTLY RAISED CRITICAL COMPONENTTEMPERATURES (e.g. NUMEROUS HIGHPOWER AND/OR LENGTHYEXPOSURES).

The existing parameters are PERMANENTLY LOST when a CLEAR menu isexecuted. A COMPLETE RECALIBRATION of the assembly (generator organtry) must therefore be performed.

WARNING

WARNING

CAUTION

INST

ALL

ATIO

N


121

39 Returning to the Application Mode

To return to the application mode press the SETUP key n times, where n is the

number of levels that you have gone down into the installation tree structure.

Note: If you have performed any calibration procedures or otherwise changed any savedparameter values, you must perform a saved parameter memory checksum beforereturning to the application mode. See Section 37. Otherwise, you will receive aCHECKSUM ERROR message.

Note: If you switch off the Senographe for any reason and then switch it on again, you must onceagain change the position of the installation menu enable switch before being able to haveaccess to the installation mode. See Section 34.

310 Configuration Parameters

3101 Gantry Present/Absent (PRS_A)

Menu accesspath: SETUP/INSTAL/CONFIG/PRS_A

The installation software provides access to a parameter called PRS_A (PReSence_Arm),whose value can be set to either YES or NO. The value of PRS_A indicates, to thesoftware, the presence or absence of the gantry,.

The value of PRS_A to NO is used by Manufacturing only.

Following a CLEAR (see section 38),PRS_A takes on the value NO.PRS_A is kept in the saved parameter memory, which means that its value is retained whenpower is turned off.

The value of PRS_A can be set by following the menu access path shown above. SelectYES or NO and perform a CKSUM.

3102 Type Selection (700T or 800T)

Menu access path: SETUP/INSTAL/CONFIG/TYPE

The installation software provides access to a parameter called TYPE (Type ofSenographe), whose value can be set to either 700T or 800T. The value of TYPEindicates to the software, the selection of Senographe configuration 700T or 800T.

Following a CLEAR (See Section 38), TYPE takes on the value 700T.The value of TYPE can be set by following the menu access path shown above. Select700T or 800T and perform a CKSUM.

INST

ALL

ATIO

N


122

3103 Display of Parameters Following an Exposure

Menu access path: SETUP/INSTAL/CONFIG/DISP

To simplify the service engineers work, the software can display certain parametersfollowing an exposure. These parameters are displayed on the console display window in twogroups which appear alternately:

kv mAs mA Time I heater

and

offset photo cell photo cell corrected thicknessHV measurement photo cell

result measurementresult

Where:

offset = offset of photo cell measurement (dark current + electrical offset)photo cell measurement result = photo cell/mA measurementcorrected photo cell measurement result = photo cell measurement result corrected accordingto Senographe configurationthickness = breast compressed thickness in cm of equivalent plexiglass

This DISP parameter is turned on and off by following the menu access path shown above.Select YES or NO. A CKSUM is NOT necessary because this parameter is not a savedparameter. When power is turned off, the value of DISP is lost and reverts to NO at thenext powerup.

INST

ALL

ATIO

N


123

3104 Calendar and Clock

Menu acces path: SETUP/INSTAL/CONFIG/DATE

The CPU is equipped with a calendar and clock that are used for the following functions:

Thermal protection cooling algorithms, whether or not the generator is turned on.

Memorization of the date and time of an equipment failure.

Last date of access to the installation mode.

The last function makes it possible for the service engineer to verify the date and time of hislast visit. He can also determine if access to the installation modes was made by unauthorizedpersons since his last visit.

The date is modified by following the menu access path shown above and then selecting

DATE. Select NEXT, then rotate the kv dial to obtain the desired day. Select

NEXT again and rotate the kv dial to obtain the desired month. Repeat once more to obtainthe desired year, then select VALID to confirm the date.

Note: The date is entered in the order DAY/MONTH/YEAR. For example, if the date to beentered is October 9, 1991, enter 09, then 10, then 91.

The time is modified by following the menu access path shown above and then selectingHOUR. Enter the time of day as explained above for the date, using the NEXT, kvdial and VALID functions.

Note: The time of day is entered in 24hour format. For example, if the time of day is 3:13:27PM, you must enter 15:13:27.

Note: Following a generator CLEAR of saved parameters, the calendar and clock, as well asthe last installation mode access date are initialized to the release date of the generatorsoftware version at 0:00:00.

3105 Visual Representation of Numerical Parameters

When displayed on the console, most numerical values appear in the form of real numbers inscientific notation floating point format with four significant figures.

Some examples follow:

1.250E+3 = 1250.00

+4.345E1 = 0.4345

+1.000E+0 = 1.000

INST

ALL

ATIO

N


124

3106 Visual Display of Parameter Values

A parameter value can be displayed on the Senographe console by accessing the calibrationmenus for the procedures that compute the parameter in question. Typically this is done whenyou are at a menu choice between CALIB and PARAM. Select PARAM to display theparameter value.

Note: If the calibration procedure computes more than one parameter, turning the kv

dial will display them one at a time in sequence.

As an example, lets look at the values of scale factor K and offset voltage VOF of tube track 1which are computed by the heater current scale factor calibration routine: follow the menuaccess path SETUP/INSTAL/GENE/HTR_SCL/TRACK1/PARAM.

On the right of the first console display line appears the value of scale factor K. Rotate the kvdial clockwise by one position. Now offset voltage VOF appears instead.

DO NOT attempt to modify these calibrated parameter values.

3107 Modification of a Parameter Value or Entry of a Measurement

Parameters are entered or modified in scientific notation form.

When at the parameter value modification or measurement entry level in the menu structure,there are two possible selections: NEXT and VALID. Begin by selecting NEXT. Thisenables modification of the first character to be entered. Successive selections of NEXTwill enable modification of each character to be entered.

Use the kv dial to modify the character being entered. Select VALID when all

characters are correctly entered.

NEVER modify a parameter value on a Senographe that has already beencalibrated unless you have a specific reason. Otherwise, doing so, in general,would necessitate entering the default parameter value(s) and completelyrecalibrating the subassembly (generator or gantry) for the parametervalue(s) in question.

CAUTION

CAUTION

INST

ALL

ATIO

N


125

As an example, lets set the maximum exposure time to 5.7 (+5.700E+0) seconds. Follow themenu access path SETUP/INSTAL/CONFIG/CONFIG/T_MAX. Select NEXT. Turn

the kv dial to set the sign of the value to be entered (in this example, the value is

positive +). Select NEXT again. Turn the kv dial to set the value of the first digit to 5.Continue selecting NEXT and turning the kv dial until you have input +5.700E+0 (mantissasign and four digits plus exponent sign and one digit). If you make a mistake, select NEXTrepeatedly until you arrive at the faulty value, then correct it by rotating the kV dial. If youtruly wish to enter the parameter value, select VALID, keeping the above CAUTION inmind before doing so! To exit the modification routine, press SETUP once.

Note: Pressing the VALID key is effective ONLY when the entire value, including exponent,is displayed. This means that if you correct a digit after making a mistake, as describedabove, you must press the NEXT key repeatedly until the entire parameter value isvisible before being able to enter the new value using the VALID key.

3108 Entry of an AlphaNumeric Value

This is the case when entering screen pair names (seven characters maximum allowed).The principle is identical to that used for parameter value entry as described in Section 3107

(repeated use of NEXT, kv dial and VALID).

Here, rotation of the kv dial gives access to the following characters:

The 26 letters of the alphabet

The ten digits from 0 to 9

The colon :

The choice of a screen pair name is confirmed by pressing VALID.

INST

ALL

ATIO

N


126

311 Principles of Generator Calibration

3111 Vocabulary

The following key words are found throughout the generator installation menus:

CALIB designates a menu that steers you to the calibration procedure itself.

PARAM designates a menu that steers you to other menus that allow you to display andmodify parameters.

CHANGE designates a menu that allows you to modify a parameter.

REF designates a menu within a calibration procedure that allows you to modify thecommand input (mAs for reference energy, photo cell HV for the frequency/HV calibration,heater current for the heater current scale factor calibration, etc...).CALCUL designates a menu that steers you to the execution of the computations necessaryto obtain the parameter values.

3112 Use of the First Trigger/Second Trigger Buttons During Installation

In general, calibration computations are started by pressing the SECOND TRIGGERbutton. (The FIRST TRIGGER button is not used during installation.)After going down through the different menus, the final CALIB selection steers you to amenu that has no second line displayed on the console display window (i.e. there are no moremenus to select). It is at this level that the calibration computation is started by pressing theSECOND TRIGGER button.

3113 Inhibit Conditions Due to Gantry Absence

The AOP calibration procedures (CELL and ALGO) need to exchange information withthe CPU.

Therefore, before performing these calibration procedures, it is necessary to set the value ofPRS_A to YES. See Section 3101. Otherwise, error messages indicating softwareabsence of the gantry will appear on the console display, and access to the CALIB menus isinhibited (only display and modification of parameters will be possible).

INST

ALL

ATIO

N


127

3114 Inhibit Conditions Due to Grid Absence/Presence

Many of the AEC calibration procedures are performed with grid and without grid. Forsuch procedures, the software indicates whether or not the grid is present. The calibrationsoftware will verify agreement between physical presence/absence of the grid and the serviceengineers choice of calibration with grid or without grid. If there is disagreement, errormessages will appear and access to the CALIB menu will be inhibited.

3115 Displayed Messages During ExposureProducing Calibration Procedures

The following messages are displayed in the upper righthand corner of the console displayduring calibration procedures that make Xray exposures:

Exposure number (when exposure is valid) Arcing

Failure (return to application mode for explicit message) Excessive temperature

End of series of exposures

Certain calibration procedures that make Xray exposures insert, in alternation with theabove messages, specific messages such as:

Too much plexi

Not enough plexi

Reduce HV, same point

Etc...

3116 Other Displayed Messages

In general, the software displays, as much as possible, messages indicating the phases ofcalibration such as:

Calibration end

Calcul done

Etc...

SECTION 4SITE PREPARATION

See PreInstallation Manual for information on site preparation.

INST

ALL

ATIO

N


128

SECTION 5INSTALLATION STEERING

The installation of the Senographe must be performed according to theCONTENT as well as the CHRONOLOGICAL ORDER given in this section.Failure to do so can result in faulty calibration of the product and subsequent lossof performance.

Note: Use the installation steering guide (see illustration 116) and the Flow Chart (seeillustration 117) as a memo to assist you during the InstallationUse IST 011 INSTALLATION FORM to record all values obtained.

1. Unpack Senographe and accessories.See Job Card IST 001 UNPACKING THE EQUIPMENT AND CHECKING.

2. Physically place, console, protective glass screen, pedals, etc.See Job Card IST 002 PHYSICAL INSTALLATION AND PROTECTIVE GLASSFITTING.

3. Attach appropriate safety labelling to the equipment according to local regulations.See Job Card IST 008 SAFETY LABELLING.

The attachment of appropriate safety labelling to the equipment is a LEGALREQUIREMENT for operation of an Xray producing unit.

4. Remove both covers cabinet and connect the console.See Job Card IST 003 REMOVAL OF CABINET COVERS AND CONSOLECONNECTION.

5. Inspect inside of cabinet for loose or disconnected cables, wires, connectors, etc. Referto MIS maps if necessary (see Schematics book).

6. Connect mains supply to cabinet and configure generator for mains voltage,.See Job Card IST 004 CONNECTION OF MAINS SUPPLY.

7. Connect room lamps wiring and room door switch (optional).See Job Card IST 005 CONNECTING ROOM LAMPS AND ROOM DOOR.

8. Check basic supply voltages.See Job Card IST 006 CHECKING BASIC POWER SUPPLY VOLTAGES.

DO NOT ACCESS THE INSTALLATION SETUP MENUS DURING THISCHECK. FOLLOW THE PROCEDURE IN THE ORDER GIVEN. DO NOTPERFORM ANY CHECKSUM OPERATIONS. EXTREMELY IMPORTANTINFORMATION ABOUT THE INTEGRITY OF THE SENOGRAPHE RAMCONTENTS CAN BE PERMANENTLY LOST IF THESE INSTRUCTIONSARE NOT FOLLOWED CORRECTLY.

CAUTION

CAUTION

WARNING

INST

ALL

ATIO

N


129

9. Check jumpers and switches.See Job Card IST 007 JUMPERS AND SWITCHES.

10. Measure free space between floor and ceiling of the room.If the available height is less than 2.5 meters (about 8.2 feet), performJob Card CAL 011 SETTING OF ELEVATOR UPPER TRAVEL LIMIT.

11. Perform the initial powerup check.

VERY IMPORTANT READ CAREFULLY:

DO NOT ACCESS THE INSTALLATION SETUP MENUS UNTIL THEINSTRUCTIONS INDICATE TO DO SO. FOLLOW THE PROCEDURE INTHE ORDER GIVEN. DO NOT PERFORM ANY CHECKSUMOPERATIONS. EXTREMELY IMPORTANT INFORMATION ABOUT THEINTEGRITY OF THE SENOGRAPHE RAM CONTENTS CAN BEPERMANENTLY LOST IF THESE INSTRUCTIONS ARE NOT FOLLOWEDCORRECTLY.

a. Turn on the Senographe and wait for the autotests to execute.b. Normally, the Senographe will now be in application mode, in the exposure mode

and configuration that it was in when last turned off before leaving the factory.

THERE SHOULD NOT BE, UNDER ANY CIRCUMSTANCES, ACHECKSUM ERROR MESSAGE ON THE CONSOLE (e.g. Checksumerror).

IF THIS MESSAGE APPEARS, COMPLETE THIS INITIAL POWERUPCHECK AND PERFORM THE SOFTWARE CONFIGURATION IN STEP 12.BELOW. THEN PROCEED TO A COMPLETE RECALIBRATION OF THESENOGRAPHE AS GIVEN IN CHAPTER 3. ONCE THISRECALIBRATION IS COMPLETED, CONTINUE WITH STEP 14. BELOW.

12. Perform software configuration.See Job Card IST 010 SOFTWARE CONFIGURATION

13. Perform Checking the mains supply for a full power useSee Job Card CAL 015 CHECKING THE MAINS SUPPLY FOR A FULL POWERUSE.

IF, DURING THE INITIAL POWERUP CHECK IN STEP 11. ABOVE,THERE WERE ANY PROBLEMS WITH CHECKSUM ERRORS, OR WITHSYSTEM LAST INSTALLATION DATE AND TIME, OR WITH CURRENTTIME AND DATE, IT IS AT THIS POINT, PRIOR TO PROCEEDING TOSTEP 14. BELOW, THAT A RECALIBRATION WOULD HAVE TO BEPERFORMED. FOR THESE PROCEDURES, SEE CHAPTER 3.

14. Perform preliminary generator and gantry testing.See Job Card IST 009 SENOGRAPHE PRELIMINARY TESTING.

WARNING

WARNING

WARNING

INST

ALL

ATIO

N


130

15. Check safelighting and film processing.See Job Card CAL 012 CHECKING SAFELIGHTING AND FILM PROCESSING.

Note 1 : For following steps :

use AEC flow chart to assist in following steering guide. See illustration 117

Note 2 : In case of error messages during the following steps, see CAL 023 for explanation ofthese messages.

16. Calibrate AEC for each screen pair (repeat steps a. to AUCUN LIEN below for eachscreen pair).a. Choose and configure a screen pair.

Perform the procedures in: Job Card CAL 006 SCREEN PAIR SELECTION AND CONFIGURATION.

b. Calibrate photo cell gain.

Perform the calibration in:Job Card CAL 007 PHOTOMULTIPLIER CELL GAIN FOR SCREEN PAIR.

c. Determine if reciprocity law failure compensation parameters (LNRT) can beentered manually. If not, perform the necessary calibration to determine them.

IF the screen and film of the screen pair being calibrated appear in table 11 below,or IF, in your own experience installing the Senographe, you have ALREADYdetermined parameters A0, A1 and A2 for the SAME screen pair, go directly tostep d..

IF this is not the case, go directly to:Job Card CAL 013 CALIBRATION OF FILM RECIPROCITY LAW FAILURECOMPENSATION FOR A GIVEN SCREEN PAIR.

Once this calibration is finished, write down the newlydetermined parameters A0,A1 and A2 for the screen pair being calibrated in table 11 below, then SKIP step d.and go DIRECTLY to step AUCUN LIEN .

INST

ALL

ATIO

N


131

TABLE 11A0, A1 AND A2 VALUES FOR VARIOUS SCREEN PAIRS

SCREEN BRANDAND TYPE FILM BRAND AND TYPE

PROCESSORCYCLE TIME

(SEC)A0 A1 A2

KODAK MINR KODAK MINR MA 90 + 8.854E2 + 3.753E1 + 2.361E3

KODAK MINR E 90 + 9.152E2 + 2.261E1 + 2.964E3

KODAK MINR H 90 + 1.481E1 + 7.495E1 + 1.095E1

KODAK MINR M 90 + 1.145E1 + 2.734E1 + 4.605E2

3M TRIMAX HM 90 + 1.000E+0 + 8.479E2 + 1.210E2

AGFA MR detail S AGFA MR5II 90 + 1.557E1 + 5.837E1 + 1.738E1

AGFA MR3II 90 + 9.599E2 + 1.777E1 + 8.994E2

AGFA MR6III 90 + 1.571E1 + 3.125E1 + 1.937E1

3M T2M 3M FM 90 + 1.570E1 + 4.357E1 + 1.440E1

3M HM 90 + 1.438E1 + 2.574E1 + 8.461E2

3M HCM 90 + 1.074E1 + 5.694E1 + 5.576E2

DUPONT Fast detail DUPONT MICROVISION 90 + 1.474E1 + 3.636E1 + 1.422E1

KODAK MINR DUPONT MICROVISION 90 + 1.041E1 + 1.347E1 + 6.556E2

KONIKA M100 KONIKA CM 90 + 1.128E1 + 5.453E1 + 3.298E1

FUJI FINE FUJI UMMH 90 + 9.297E2 + 6.245E1 + 1.944E3

FUJI UMMA 90 + 7.061E2 + 4.715E1 + 1.702E3

d. Calibrate reference energy.Enter manually the three reciprocity law failure compensation parameters (A0, A1and A2) either from table 11 or from your own notes from a previous installationof the same screen pair on another Senographe for the screen and film of the screenpair being calibrated:Starting from application mode, selectSETUP/INSTAL/AOP/ALGO/FSC=x/CALIB/LNRT/PARAM on the console,where x is the screen pair indicator (A,B,C,D,E) corresponding to the screen pairbeing calibrated.See Job Card CAL 006 SCREEN PAIR SELECTION AND CONFIGURATION.

At this point, enter the three parameter values by using the CHANGE key, rotatingthe kV dial and using the NEXT, VALID and SETUP keys. See sections 3106 and3107.If this is an additional Senographe 700T or 800T, at the same site, using the sameprocessor, then as soon as the three parameter values are correctly entered, goIMMEDIATELY to:Job Card IST 014 CALIBRATION OF REFERENCE ENERGY FOR A GIVENSCREEN PAIR

INST

ALL

ATIO

N


132

Once this calibration is finished, go directly to step AUCUN LIEN below.Otherwise, go directly to Job Card IST 013 calibration of film reciprocity failurecompensation for a given screen pair. Once this calibration is finished, write downthe newlydetermined parameters A0, A1 and A2 for the screen pair being calibratedin table 1.

17. Change console dialog display language to that of the country of installation (if other thanEnglish):Starting from application mode, select SETUP/MEDICAL/1/2/LANGUAGE/language on the console, where language isthe desired console dialog display language (FRANC, ENGL, DEUTS, ESPAN, ITALIorPORTU).

18. Switch off the Senographe to disable access to Installation Menu.

19. Refit cabinet covers.See Job Card IST 003 REMOVING AND REINSTALLING THE CABINETCOVERS AND CONSOLE CONNECTION.

INST

ALL

ATIO

N


133

ILLUSTRATION 116STEERING GUIDE FLOWCHART

Unpacking the equipmentand Checking

IST 00130 min

Physical Installation andProtective glass fitting

IST 00260 min

Safety Labeling

IST 0085 min

Removal of Cabinet side coversand Console Connection

IST 00310 min

Connection of Mains Supply

IST 00430 min

Connection room lamps androom door (optional)

IST 00530 min

Checking BasicPower Supply Voltages

IST 00615 min

Jumpers and Switches

IST 00710 min

Setting of Elevator UpperTravel Limit

CAL 0110 to 30 min

POWER ON

Software configuration

IST 0105 min

SenographePreliminary testing

IST 00930 min

Checking SafeLighting andFilm Processing

CAL 01230 min

AEC Calibration(see AEC Flow Chart, illus 117) 35 to (90/140 min)

Switch off to disable accessto Install Menu

ReInstallation Cabinet Covers

IST 00310 min

Call

GE

Service

ChecksumError CodesDisplayed?

use LNRT parameters fromtable 1 if possible

Note: Time (in minutes) is an averagevalue for indication purpose only.

Note: Use IST 011Calibration formto recordall obtained values.

YES

NO

Checking the mains supply for

CAL 015a full power use

INST

ALL

ATIO

N


134

ILLUSTRATION 117FLOW CHART OF AEC/AOP CALIBRATION

For Installation, dontperform CAL 004and CAL 005.Calibrated byManufacturing

Time : 15

NO

YES

NOTE 1

DO NOT FORGET : DO BOTH COPY IE.G. : A no screen TO B no screen

ANDA with screen TO B with screen

NOTE 2

IF LNRT PARAMS ARE UNKNOWNPERFORM CAL 13 IMMEDIATELY

AFTER CAL 07 (SO, WITH HOT TUBE)

Time (in minutes) is an averagevalue for indication purpose only

YES

HV_PM INTERNALVOLTMETER

CALIBRATIONCAL 004 Section.5

CAL 004 Section .6

DACCALIBRATION

CALIBRATIONCAL 005

PM/HV_PM

COUPLE CHOICE(NAME, VALIDATION)

CAL 006

Time : 40

Time : 5

PM YIELDSee Note 2CAL 007

ONEFILM/SCREEN

COUPLEALREADY

CALIBRATED? ?

COUPLE CHOICE

Time : 5

REFERENCE ENERGYCAL 014

Time : 20

END

PM YIELD


CAL 006

PARAMETERS DUPLICATIONCopy only parameters without

screen

CAL 007,Section5.2 step 2. to step 7.

Perform only calibrationwith screen

CAL 007Section 6.5, 6.6, 6.7, 6.10 and 6.11

Time : 5

Time : 5

Time : 20

LNRTPARAMS

ALREADYKNOWN

? ?

CALIBRATEANOTHERCOUPLE

? ?

DIFFERENTSCREEN? ?

PARAMETERSDUPLICATION

See Note 1 below

CAL 007Section 5.2

step 2. to step 12.


CAL 006

Time : 5

Time : 5

NEEDONLY

TO SHIFTAVERAGEDENSITY

? ?NO

YES

YES

NO

YES NO

END

ENTER KNOWNPARAMETERS

(A0, A1, A2)from steeringguide table

path = AOP/ALGO/FSC = x../CALIB/LNRT..

/PARAM/CHANGE

Time : 5

REFERENCE ENERGYCAL 014

Time : 20

REFERENCE ENERGYCAL 013 Section 62

HEATERCALIBRATION

CAL 013 Section 61Time : 10

Time : 25

LNRT

CAL 013 Section 63

Time : 45 to 80

NO

INST

ALL

ATIO

N


135

SECTION 6INSTALLATION JOB CARDS

JOB CARD No. PURPOSE

IST 001 UNPACKING THE EQUIPMENT AND CHECKING

IST 002 PHYSICAL INSTALLATION AND PROTECTIVE GLASS FITTING

IST 003 REMOVING AND REINSTALLING THE CABINET COVERS AND CONSOLECONNECTION

IST 004 CONNECTION OF MAINS SUPPLY

IST 005 CONNECTING ROOM LAMPS AND ROOM DOOR (OPTIONAL)IST 006 CHECKING BASIC POWER SUPPLY VOLTAGES

IST 007 JUMPERS AND SWITCHES

IST 008 SAFETY LABELLING

IST 009 SENOGRAPHE PRELIMINARY TESTING

IST 010 SOFTWARE CONFIGURATION

IST 011 INSTALLATION FORM

INST

ALL

ATIO

N


136

Blank page.

INST

ALL

ATIO

N

Version No.:

Senographe 700T and 800T Job Card IST 001 1 of 2

Purpose: UNPACKING THE EQUIPMENT ANDCHECKING Date: Dec. 18, 1995

Time: x h xx min Personnel:


137

SECTION 1SUPPLIES

None.

SECTION 2TOOLS

Ratchet wrench with 22 mm socket.

6mm Allen wrench.

Claw hammer or other suitable tool for removing packing nails.

SECTION 3SADETY PRECAUTIONS

Follow standard safety pratices for handling and moving large machines.

Never lift or move the Senographe by its the arm handles and by the imagereceptor.

SECTION 4PREREQUISITES

None.

CAUTION

INST

ALL

ATIO

N Job Card IST 001 2 of 2UNPACKING THE EQUIPMENT AND CHECKING


138

SECTION 5UNPACKING THE EQUIPMENT

The objective is to unpack the Senographe and accessories from the crate, move them to the mammographyroom and checking quickly the content of each accessory boxes.

5.1 Inpect for damage and perform initial unpacking

The Senographe was completely inspected for proper operation and appearance before shipment. However, itis necessary to inspect the product after the shipment is received. Visually inspect the packages for anyapparent damage. If there are signs of damage, refer to the Damage in Transportation statement in the front ofthis manual.

5.2 Unpacking equipment

1. Remove the accessory packages from the palette.

2. Use the ratchet wrench with a 13 mm socket to remove the four Senographe baseplate shipping holdholddown screws.

3. Remove the four wooden support blocks in place between the palette and the Senographe baseplate.

Note: Keep one of four wooden support blocks because it will be used to install the protective glass.

4. When the Senographe is fully supported by the castors, take the Senographe down from the palette inusing the ramp.


5. Move the Senographe and the other accessory packages into mammography room.

6. Open the packages and refer to the Product Delivery Instruction (PDI) from OPEN ME FIRSTenvelope. Verify the items on the list, are present in the packages. Each package is numbered. Carefullyexamine the contents for small parts.

CAUTION

INST

ALL

ATIO

N

Version No.: A


Purpose: PHYSICAL INSTALLATION ANDPROTECTIVE GLASS FITTING Date: Dec. 18, 1995

Time: 1 hour Personnel:


139

SECTION 1SUPPLIES

None

SECTION 2TOOLS

Rachet wrench with 17 mm socket

8 mm Allen wrench

5 mm Allen wrench

Screwdrivers

SECTION 3SAFETY PRECAUTIONS

Follow standard safety pratices for handling and moving large machines.



Job Card IST 001 UNPACKING THE EQUIPEMENT AND CHECKING Job Card IST 003 REMOVAL OF ELECTRONIC CABINET COVERS

(Section 5 point 5.1 only).

CAUTION

INST

ALL

ATIO

N Job Card IST 002 2 of 4PHYSICAL INSTALLATION AND PROTECTIVEGLASS FITTING


140

SECTION 5PHYSICAL INSTALLATION

The objective is to physical place the Senographe in its position, and to fit the protective.5.1 Install the Senographe into its position.

Note: Before you proceed, it is recommended to perform a final verification of the information given in thePreInstallation Manual.

1. Wheel the Senographe to the right position.

2. Detach the protective glass from the Senographe and put it safe area.

3. Remove the protective glass holder fixed on the castor.

4. Place the four flat round jack feet on the floor with their nipples facing upwards.5. Turn the four jacking bolts downwards until their hollowed ends engage with the nipples of the four

jack feet.6. Use the rachet wrench with 17 mm socket to progressively jack the Senographe up via the four jacking

bolts until the castors are clear of the floor.

7. Use the 8 mm Allen wrench to remove the castors.

8. Lower the Senographe progressively via the four jacking bolts until it is fully supported by itsbaseplate. Remove the four jacking bolts completely.

Note: The four jack feet remain below the Senographe baseplate.

9. Install the four short leveling screws into the jacking holes and adjust till the Senographe 700T and800T is level. It is NOT necessary to perfectly level the base, only to ensure it is sitting firmly on all fourjacking feet and approximatly level.

10. Cover all base plate holes external to the cabinet with the plastic caps provided.

Remove locking rods for column movements.

11. Put in place the appropriate caps to hide the locking rod holes (caps are delivered in the installation kit).12. Save castors, jacking bolts, the wooden block and locking rods for future service needs.

CAUTION

INST

ALL

ATIO

NJob Card IST 002 3 of 4PHYSICAL INSTALLATION AND PROTECTIVEGLASS FITTING


141

5.2 Fit the protective glass.

The glass weighs 40 kg and should, therefore, be handled with care.

1. Unpack the protective glass.

2. Mount the protectrive glass attachment rail with four screws from installation kit.

3. Referring to Illustration 1 for details, assemble four mounting screw assemblies (A) as shown at B inthe holes at the edge of the glass (the other two are for the control panel holder).

4. Place the protective glass on the wooden block (from the Senographe packaging) and slide it carefullyup to the mounting bracket on the column.

5. Position the protective glass so that you can slide the screws into their securing holdes (arrow 1 inIllustration 2)

6. Position the glass so that you can slide the screws into their securing holes (arrow 1 in Illustration 2).

MAKE SURE ALIGNMENT OF THE PLASTIC PARTS WITH THESCREWS IS PERFECT TO AVOID DAMMAGE OF THREATS.

7. Making sure the black gaskets (see arrows 1 in Illustration 1) remain in place, tighten the four screwssecurely.

8. Position the supporting foot (arrow 2 in Illustration 2) with the shaped gaskets between the glass andthe foot, and the shaped metal piece between the Allen screws and the gasket.

9. Remove the wooden block and adjust the height of the foot until it is just supporting the weight of theglass, then tighten the Allen screw on the moveable part of the foot.

10. Place the two remaining screw assemblies in the holes in the middle of the glass (arrow 3 inIllustration 2) and mount the control panel holder.

11. Slide the control panel into this holder.

CAUTION

WARNING

INST

ALL

ATIO

N Job Card IST 002 4 of 4PHYSICAL INSTALLATION AND PROTECTIVEGLASS FITTING


142

ILLUSTRATION 1GLASS MOUNTING SCREW ASSEMBLY

1 1

A B

ILLUSTRATION 2LOCATION OF SECURING PARTS ON THE GLASS

2

1

3

1

1

1

2

INST

ALL

ATIO

N

Version No.:


Purpose: REMOVING AND REINSTALLING THE CABINETCOVERS AND CONSOLE CONNECTION Date: Dec. 18, 1995

Time: 10 min Personnel:


143

SECTION 1SUPPLIES

None.

SECTION 2TOOLS

Engineers standard toolkit.

SECTION 3SPECIAL SAFETY PRECAUTIONS

None.

SECTION 4PREREQUISITTES

The chronological order given (see Section 5, in Chapter 1, INSTALLATION STEERING must befollowed).

INST

ALL

ATIO

N Job Card IST 003 2 of 4REMOVING AND REINSTALLING THE CABINETCOVERS AND CONSOLE CONNECTION


144

SECTION 5TASK DESCRIPTION

The objective is to remove, reinstall the cabinet covers and to connect the console.5.1 Removing the covers

There are three covers on the cabinet the top cover clips on and the two side covers are held by screwsaccessible when the top has been removed.

1. To remove the top cover, pull upwards in the areas shown by arrows 1 it may be necessary to give asharp tug to pull it free of the retaining clips.

2. Unscrew the two screws (location shown by arrows 2) on each side cover and lift the covers, one at atime, free of the pins holding the bottom edge in place disconnect the grounding wires and remove thepanels to a safe place.

5.2 Routing and connecting console cable

1. Locate connector J5 on 300PL9 Power Supply Board and connect the console cable to it (seeillustration 4).

2. Route console cable (provided in the accesssory pack) as show Illustration 3, arrows 3.3. Connect opposite end of console cable to the console.

5.3 Re-installing the covers

Re-installing the covers is the reverse order of removal (see Section 5.1).

INST

ALL

ATIO

NJob Card IST 003 3 of 4REMOVING AND REINSTALLING THE CABINETCOVERS AND CONSOLE CONNECTION


145

ILLUSTRATION 3REMOVING THE COVERS

11

22

INST

ALL

ATIO

N Job Card IST 003 4 of 4REMOVING AND REINSTALLING THE CABINETCOVERS AND CONSOLE CONNECTION


146

ILLUSTRATION 4CABLE ROUTING

Routing consolecable

300PL9 J5

INST

ALL

ATIO

N

Version No.:


Purpose: CONNECTION OF MAINS SUPPLYDate: Dec. 18, 1995

Time: 30 min Personnel:


147

SECTION 1SUPPLIES

None.

SECTION 2TOOLS

A.C. voltmeter.

Pliers (for cable clamp).

SECTION 3SAFETY PRECAUTIONS

Follow standard safety techniques and procedures for handling equipment and circuits that can come intocontact with mains supply voltages.


The chronological order given in Installation Steering Guide must be followed.

INST

ALL

ATIO

N Job Card IST 004 2 of 6CONNECTION OF MAINS SUPPLY


148

SECTION 5CONNECTION OF MAINS SUPPLY

The objective is to determine characteristics (i.e. nominal voltage and number of phases) of the availablepower source, configure the Senographe accordingly, and connect it to the power source.

5.1 Determine if available mains supply is one phase and neutral or two phases

If one phase and neutral mains supply is available in the mammography room, use the phase and the neutralto power the Senographe by wiring it according to the Illustration 1.

Verify that the wire from the hospital power marked as neutral is in fact neutral.

If two phases are available, wire the Senographe according to the Illustration 2.

Take special care to configure F1, F2 or the metal cylinder as specified in Section 5.4.

ILLUSTRATION 1ONE PHASE AND NEUTRAL MAINS SUPPLY

Ground WirePE

Neutral WireL2/N

Phase 1 WireL1

INST

ALL

ATIO

NJob Card IST 004 3 of 6CONNECTION OF MAINS SUPPLY


149

ILLUSTRATION 2TWO PHASES MAINS SUPPLY

Ground WirePE

Phase 2 WireL2/N

Phase 1 WireL1

5.2 Configure Fuses F1, F2 or the metal cylinder

Follow the indications on the label located on the bottom of the cabinet on the Mains Fuse Disconnector300 S1, for the configuration. Also see Illustration 3 below.

TO ASSURE SAFE OPERATION OF THE SENOGRAPHE. BE SURETO DETERMINE IF THE MAINS SUPPLY CONSISTS OF TWOPHASES OR A SINGLE PHASE WITH NEUTRAL. FOR ASINGLEPHASE WITH NEUTRAL MAINS SUPPLY, A METALCYLINDER (DELIVERED WITH THE SENOGRAPHE) MUST BEINSTALLED IN PLACE OF F2.

ILLUSTRATION 3FUSE CONFIGURATION

L2/N L1

Configuration with1 Phase and Neutral

FUSE F1 25AMetal Cylinder

L2/N L1

Configuration with2 Phases

FUSE F1 25AFUSE F1 25A

WARNING

INST

ALL

ATIO

N Job Card IST 004 4 of 6CONNECT

Documents

Service Manual 800 Tsm