Centre Scientifique et Technique du Bâtiment 84, avenue Jean Jaurès – Champs sur Marne Boîte Postale 02 F-77447 Marne la Vallée Cedex 2 Tél. : (33) 01 64 68 82 82 Fax : (33) 01 60 05 70 37
Autorisé et
notifié conformément à
l’article 10 de la directive
89/106/EEC du Conseil, du 21 décembre 1988, relative au
rapprochement des dispositions
législatives, réglementaires et administratives des Etats
membres concernant
les produits de construction.
MEMBRE DE L’EOTA
European Technical Approval ETA-09/0041 (English language translation, the original version is in French language)
Nom commercial :
Trade name: VETISOL MODULPIERRE / MODULISS / ELITE
Titulaire :
Holder of approval: VETISOL
ZI SUD
890, rue des Frères Lumière
FR-71000 MACON
Type générique et utilisation prévue du produit de construction :
Kit de vêture
Generic type and use of
construction product:
Veture kit – Prefabricated unit for external wall insulation
Validité du : au :
Validity from / to:
30/05/2013
30/05/2018
Usine de fabrication :
Manufacturing plant: VETISOL
ZI SUD
890, rue des Frères Lumière
FR-71000 MACON
Le présent Agrément technique européen contient :
This European Technical Approval
contains:
28 pages incluant 14 figures faisant partie intégrante du document.
28 pages including 14 drawings which form an integral part
of the document.
This European Technical Approval replaces ETA-09/0041 with validity from 30/05/2013 to 30/05/2018
Cet Agrément Technique Européen remplace l’Agrément ETA-09/0041 valide du 30/05/2013 au 30/05/2018
Organisation pour l’Agrément Technique Européen
European Organisation for Technical Approvals
Page 2 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
I LEGAL BASES AND GENERAL CONDITIONS
1. This European Technical Approval is issued by the Centre Scientifique et Technique du Bâtiment in accordance with:
- Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products
1, modified by
the Council Directive 93/68/EEC of 22 July 19932;
- Décret no. 92-647 du 8 juillet 19923 concernant l’aptitude à l’usage des produits de
construction;
- Common Procedural Rules for Requesting, Preparing and the Granting of European Technical Approvals
set out in the Annex of Commission Decision 94/23/EC
4;
- Guideline for European Technical Approval of « Veture kits – Prefabricated units for external wall insulation » ETAG 017, edition 2005.
2. The Centre Scientifique et Technique du Bâtiment is authorised to check whether the provisions of this European Technical Approval are met. Checking may take place in the manufacturing plant (for example concerning the fulfilment of assumptions made in this European Technical Approval with regard to manufacturing). Nevertheless, the responsibility for the conformity of the products with the European Technical Approval and for their fitness for the intended use remains with the holder of the European Technical Approval.
3. This European Technical Approval is not to be transferred to manufacturers or agents of manufacturer other than those indicated in page 1; or manufacturing plants other than those indicated in page 1 of this European Technical Approval.
4. This European Technical Approval may be withdrawn by the Centre Scientifique et Technique du Bâtiment pursuant to Article 5 (1) of the Council Directive 89/106/EEC.
5. Reproduction of this European Technical Approval including transmission by electronic means shall be in full. However, partial reproduction can be made with the written consent of the Centre Scientifique et Technique du Bâtiment. In this case, partial reproduction has to be designated as such. Texts and drawings of advertising brochures shall not contradict or misuse the European Technical Approval.
6. The European Technical Approval is issued by the approval body in its official language. This version corresponds to the version circulated within EOTA. Translations into other languages have to be designated as such.
1 Official Journal of the European Communities no. L 40, 11.2.1989, p. 12
2 Official Journal of the European Communities no. L 220, 30.8.1993, p. 1
3 Journal officiel de la République française du 14 juillet 1992
4 Official Journal of the European Communities no. L 17, 20.1.1994, p. 34
Page 3 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
II SPECIFIC CONDITIONS OF THE EUROPEAN TECHNICAL APPROVAL
1 Definition of product and intended use
The veture kit “VETISOL MODULPIERRE / MODULISS” is designed and installed in accordance with the ETA-holder design and installation instructions deposited with the “Centre Scientifique et Technique du Bâtiment”. It comprises the following components, which are factory-produced by the ETA-holder or a supplier. The ETA-holder is ultimately responsible for the system.
1.1 Definition of product
Veture unit (fig. 1)
Expanded polystyrene panels with rendering made of polymeric and cementitious binders.
The finishing and aspect are obtained by application of marble grains (Modulpierrre / Modulpierre force) or polymeric coating (Moduliss).
Standard dimensions (L x H) or (H x L)
300 x 600 mm 600 x 1200 mm
450 x 600 mm 600 x 2400 mm
600 x 600 mm
Non-standard dimensions (L x H) or (H x L)
600 x 200 to 2 700 mm
Thickness of insulation layer
55, 65, 80 and 100 mm
Thickness of veture unit (insulation and coating)
60, 70, 85 and 105 mm
Profiles (fig. 2 and 2bis)
Veture units are fixed to the substrate by aluminium alloy T or H profiles
Fixings (fig. 3 and 4)
Profiles are fixed to the wall by 8 mm plastic anchors expansion sleeve with a collar and a galvanized or stainless steel screw or nail with flat head, having an ETA in accordance with ETAG Guideline 014 “Plastic anchors for fixings of external thermal insulation of composite systems with rendering”.
Page 4 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
1.2 Intended use
This Veture kit is intended for use as external insulation of buildings’ walls. It is applied on flat and vertical walls made of masonry (bricks, blocks, stones, …) or concrete (cast on site or as prefabricated panels).
The provisions made in this European Technical Approval (ETA) are based on an assumed intended working life of at least 25 years, provided that the installed kit is subjected to an appropriate use and maintenance.
The indications given as to the working life cannot be interpreted as a guarantee given by the manufacturer, but should only be regarded as a means for choosing the appropriate products in relation to the expected economically reasonable working life of the works.
Page 5 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
2 Characteristics of product and methods of verification
2.1 Components’ characteristics
2.11 Skin
The Skin is made of render containing:
White Portland composite cement EN 197-1 CEM II / B – LL 32,5 R
0,1 to 2 mm siliceous sand
Water dispersion
Pigments made of metal oxide,
Several additives.
The dimensions and characteristics are defined below:
Thickness in the middle area : 6 mm
Specific mass : 2,1 kg/dm3
Dry extract: 93 %
Finishing coating: crushed marble aggregate :
0,5 to 2 mm
3 to 6 mm
6 to 9 mm
Polymeric coating : acrylic
Water vapour permeability of render (EN 12572: 23°C/50%HR/NH4H2PO4):
43,68 10-14 kg/(m.s.Pa) equal to Sd = 3 m
2.12 Insulation product
The expanded polystyrene panels are according to EN 13163. The description and characteristics are defined in the table below.
Descriptions and characteristics
Standard EPS Graphite EPS
Reaction to fire EN 13501-1 E E
Thickness (mm)
57 67 82 102
82 102
Length (mm) EN 13163 ± 3 mm
Width (mm) EN 13163 1 mm
Density (kg/m3) EN 13163 ≥ 15 kg/m
3
Dimensional stability under laboratory condition
EN 13163 ≤ 0,5 mm/m
Water absorption by capillarity EN 13163 0,03 kg/m2
µ EN 12524 60
Traction EN 13163 ≥ 1,8 daN/cm2
Compression EN 13163 ≥ 0,5 daN/cm2
D declared value (W/(m².K)) EN 13163 0,038 0,032
Insulation products are certified by ACERMI
Page 6 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
2.13 Veture units
Descriptions and characteristics
Veture unit
Reaction to fire F
Thickness (mm) + 0,5 / - 1
Length (mm) 1 for 300 to 600 mm
2 for 600 to 2700 mm
Width (mm) - 1/+ 0,5
Squareness (mm) 1 for 300 to 600 mm
2 for 600 to 2700 mm
Flatness (mm) 2,0
Bond strength (MPa) 0,18
2.14 Profiles
The horizontal profiles are made of aluminium alloy EN AW 6060 T5 in accordance with EN 755-2.
Their length is 3 m.
2.15 Fixings to the substrate
The T or H profiles are fixed to the substrate by anchors made of a plastic expansion sleeve (diameter 8 mm) with a collar (minimal diameter 11 mm) and of an electrogalvanized or stainless steel screw or nail (diameter 6 mm) with flat head (minimal diameter 10 mm), having an ETA in accordance with ETA Guideline 014.
2.2 Methods of verification
The assessment of the fitness for use of the Veture kit for the intended use in relation to the requirements for safety in case of fire, hygiene, health and environment, safety in use, protection against noise, energy economy and heat retention ; in sense of Essential Requirements 2 to 6 has been made in accordance with the Guideline for European Technical Approval for Veture kit – Prefabricated units for external wall insulation, ETAG 017.
2.21 Safety in case of fire
Reaction to fire : Euroclass F (No performance determined)
Page 7 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
2.22 Hygiene, health and environment
2.221 Watertightness and water permeability
Taking into account the geometry of Veture unit and open joints equipped with a pressure equilibrium space, the degree of Watertighness of this kit is determined without test.
A limited amount of water can reach the substrate (Type I as defined in ETAG 017).
2.222 Water vapour permeability (resistance to water vapour diffusion)
The water vapour permeance (W) is equal to:
Thickness (mm) Characteristic
60 3,31.10-11
kg/(m².s.Pa)
70 2,75.10-11
kg/(m².s.Pa)
85 2,64.10-11
kg/(m².s.Pa)
105 2,26.10-11
kg/(m².s.Pa)
2.223 Capillarity
Water absorption by capillarity :
< 0,3 kg/m2 after 1 hour
0,3 kg/m2 after 24 hours
2.224 Dangerous substances
Manufacturer declared to be conform to the council Directive 67/548/EEC, published in “Official Journal of the European Communities” and its amendments.
In addition to the specific clauses relating to dangerous substances contained in this ETA, there may be other requirements applicable to the Veture kits falling within its scope (e.g. transposed European legislation and national laws, regulations and administrative provisions). In order to meet the provisions of the EU Construction Product Directive, these requirements need also to be complied with, when and where they apply.
Page 8 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
2.23 Safety in use
2.231 Wind suction test
The distance between rail fixings is 600 mm.
Test specimen Failure value Q
Type of failure
Dimensions of veture unit (H x L): 600 x 600 mm Thickness: 85 mm Horizontal T profile Vertical T profile
5 000 Pa Without failure
Dimensions of veture unit (H x L): 600 x 600 mm Thickness: 60 mm Horizontal T profile Vertical T profile
5 150 Pa Without failure
Dimensions of veture unit (H x L): 450 x 600 mm Thickness: 60 mm Horizontal T profile Vertical T profile
5 500 Pa Without failure
Dimensions of veture unit (H x L): 600 x 2400 mm Thickness: 60 mm Horizontal H profile only
5 800 Pa Failure of the EPS
2.232 Bond strength between skin and insulation product
The initial characteristic bond strength of this veture unit is 0,18 N/mm2 at least. The rupture is
always 90 % cohesive.
2.233 Resistance of grooved insulation
For T and H profiles
Vêture unit
(Thickness in mm)
Average value
(N)
Characteristic value
(N)
≥ 105 355 299
≥ 85 278 247
≥ 60 205 125
2.234 Pull-through resistance of fixings from profiles
The average value is 2502 N and characteristic value is 1990 N.
Page 9 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
2.235 Dead load test
Test specimen Middle rail deflection value (mm)
Initial After 1 hour After 2 hours After 4 hours
Dimensions of veture unit (H x L): 600 x 300 mm Thickness: 60 mm Horizontal H profile
1,1 1,1 1,1 1,1
Dimensions of veture unit (H x L): 600 x 300 mm Thickness: 80 mm Horizontal H profile
1,3 1,3 1,3 1,3
The deformation of profile is assessed compatible with the veture kit.
2.236 Resistance to horizontal point loads
During the test, no permanent deflection, failure or perforation of the skin are noted.
The veture kit is capable of accommodating the horizontally applied loads acting its surface arising from maintenance, without any reduction in its performances.
2.237 Impact resistance
The distance between rail fixings is 600 mm.
Test specimen Categories
Dimensions of veture unit (H x L): 600 x 600 mm Thickness of unit: 85 or 60 mm Horizontal T profile
III
2.238 Shatter properties
Before and after impact test, this Veture kit doesn’t present sharp or cutting edges.
Page 10 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
2.24 Thermal resistance
The Calculation of the overall U-value of the wall and the veture kit (thermal bridges included) :
HLnLLUU croisement
fixationfixationrailrailrainurerainurecp.
... W/m².K
Uc : thermal U-value for the whole wall, W/(m².K),
rainurel : -value for the thermal bridges due to vertical and horizontal grooved element,
W/(m.K),
rail : -value for the thermal bridges due to profiles, W/(m.K),
Lrainure : length of the vertical and horizontal grooved element, m: HL
HLLrainure
.
L : length of the veture unit, m,
H : height of the veture unit, m,
Lrail : length of the profile, m,
Nfixation : density of fixings by m2,
χ fixation : χ-value for the punctual thermal bridges due to rail fixing, W/(K),
χ croisement : χ-value for the punctual thermal bridges due to crossing between the grooves of
veture unit and the profile, W/(K),
The thermal U-value for the whole wall (structure + VETURE), calculated with:
si
m
m
p
p
se
c
Ree
R
U1
W/m².K
Rsi, Rse : inside and outside film resistance, m².K/W,
ep : EPS thickness, m,
λp : thermal conductivity of the insulation layer, W/m.K,
em : wall thickness, m,
λm : thermal conductivity of the wall, W/m.K,
Page 11 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Installation of Veture kit on 200 mm concrete wall - Values for thermal bridges
Polystyren =0,032 W/m.K
TYPE
Old
Old
Old
Ne
w
Ne
w
Ne
w
Ne
w
Thikness (mm) 70 85 105 60 70 85 105
Uc (W/m².K) 0,43 0,36 0,29 0,49 0,43 0,36 0,29
rainure (W/m.K) 0,003 0,003 0,002 0,004 0,003 0,003 0,003
rail T (W/m.K) 0,007 0,004 0,003 0,010 0,006 0,004 0,003
rail H (W/m.K) 0,020 0,028 0,037 0,029 0,036 0,045 0,054
vis with T profile (W/K) 0,002 0,003 0,004 0,002 0,004 0,005 0,006
croisement with H profile
(W/K)0,000 0,001 0,001 0,001 0,001 0,002 0,002
croisement with T profile (W/K) Negligible 0,001 Negligible 0,001 0,001
Polystyren =0,038 W/m.K
Type
Old
Old
Old
Ne
w
Ne
w
Ne
w
Ne
w
Thickness (mm) 70 85 105 60 70 85 105
Uc (W/m².K) 0,49 0,41 0,34 0,58 0,50 0,42 0,34
rainure (W/m.K) 0,003 0,003 0,002 0,004 0,003 0,003 0,003
rail T (W/m.K) 0,008 0,005 0,003 0,011 0,007 0,005 0,003
rail H (W/m.K) 0,023 0,032 0,042 0,033 0,040 0,051 0,061
vis with T profile (W/K) 0,002 0,003 0,004 0,002 0,004 0,005 0,006
croisement with H profile (W/K) 0,000 0,001 0,001 0,001 0,001 0,002 0,002
croisement with T profile (W/K) Negligible 0,001 Negligible 0,001 0,001
Values for thermal bridges due to fixings is negligible for H profile
Page 12 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Installation of Veture kit on 250 mm bricks masonry wall - Values for thermal bridges
Polystyrène =0,032 W/m.K
Type
Old
Old
Old
Ne
w
Ne
w
Ne
w
Ne
w
Thickness (mm) 70 85 105 60 70 85 105
Uc (W/m².K) 0,36 0,31 0,26 0,41 0,36 0,31 0,26
rainure (W/m.K) 0,002 0,002 0,002 0,003 0,002 0,002 0,002
rail T (W/m.K) 0,005 0,003 0,002 0,007 0,005 0,003 0,002
rail H (W/m.K) 0,014 0,021 0,028 0,019 0,025 0,032 0,039
vis with T profile (W/K) 0,001 0,002 0,003 0,002 0,003 0,003 0,004
croisement with H profile (W/K) Negligible 0,001 0,001 0,001 0,001 0,001
croisement with T profile (W/K) Negligible 0,001
Polystyren =0,038 W/m.K
Type
Old
Old
Old
Ne
w
Ne
w
Ne
w
Ne
w
Thikness (mm) 70 85 105 60 70 85 105
Uc (W/m².K) 0,41 0,35 0,30 0,47 0,41 0,35 0,30
rainure (W/m.K) 0,002 0,002 0,002 0,003 0,002 0,002 0,002
rail T (W/m.K) 0,005 0,004 0,002 0,007 0,005 0,004 0,002
rail H (W/m.K) 0,015 0,022 0,030 0,021 0,026 0,034 0,043
vis with T profile (W/K) 0,001 0,002 0,003 0,002 0,002 0,003 0,004
croisement with H profile(W/K) Negligible 0,001 0,001 0,001 0,001
croisement with T profile (W/K) Negligible 0,001
Values for thermal bridges due to fixings is negligible for H profile
2.25 Temperature, humidity and shrinkage
After hygrothermal cycling, no deterioration of the specimen is occurred.
The bond strength value (0,145 MPa) is greater than 75 % of the initial value (0,180 MPa).
2.26 Freeze-thaw
The water absorption of the veture unit is less than 0,5 kg/m2 after 24 hours.
The freeze/thaw test was not carried out.
Page 13 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
2.27 Dimensional stability
2.271 Skin
The Value is 0,01 mm/m.K
2.272 Insulation product
The EPS panels have been stabilized at ambient conditions to obtain a dimensional stability less than 0,5 mm/m.
2.273 Thermal shock cycles on the kit
The Veture kit was not tested by thermal shock cycles, because it was tested by hygrothermal cycles.
2.28 Chemical and biological resistance
From experience, this veture kit is not known to be sensitive to chemical and biological attack.
2.29 Corrosion
This veture kit is not known to be sensitive to corrosion.
The rails made of aluminium alloys are resistant to corrosion.
Their fixings are anchors made of a plastic expansion sleeve and of electrogalvanized or stainless steel screw or nail. There are protected by the veture units and not directly exposed to outdoor atmosphere.
3 Evaluation of Conformity and CE-marking
3.1 Attestation of conformity system
Considering the Euroclass F for the reaction to fire, the system of attestation of conformity specified by the European Commission is system 4 for the reaction to fire and system 3 for other product characteristics, described in the Council Directive 89/106/EEC Annex III, 2 (ii), First possibility and is detailed as follows:
System 3: Declaration of conformity of the product by the manufacturer on the basis of:
(a) tasks for the manufacturer:
- Factory Production Control.
(b) Tasks for the notified body:
- initial type-testing of the product.
System 4: Declaration of conformity of the product by the manufacturer on the basis of:
a) tasks for the manufacturers:
- Factory Production Control. - Initial type testing of the product,
Page 14 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
3.2 Responsibilities
The ETA-holder has a factory production control system in its plant and exercises permanent internal control of production, including testing of samples in accordance with a test plan
(1).
For the components of the Veture kits which he does not manufacture himself, he makes sure that another factory production control carried out by the other manufacturers gives the guaranty of the components compliance with the European Technical Approval.
The test plan(1)
and the provisions taken by the ETA-holder for components not produced by himself has been agreed with the approval body and deposited at the CSTB. This test plan
(1)
will be given to the approved body chosen by the ETA-holder to perform the foreseen tasks on attestation of conformity.
The manufacturer shall only use raw materials supplied with the relevant inspection documents as laid down in the test plan
(1). The incoming raw materials shall be subjected to verifications by
the manufacturer before acceptance.
All the elements, requirements and provisions adopted by the manufacturer are documented in a systematic manner in the form of written policies and procedures. This production control system ensures that the Veture kits and the components are in conformity with the European Technical Approval.
The results of factory production control are recorded and evaluated. The records include at least the following information:
- designation of the product, basic material and components; - type of control or testing; - date of the product’s manufacture and date of testing of the product or basic materials and
components; - results of controls and testings and, if appropriate, comparison with requirements; - signature of person responsible for factory production control.
On request, the records shall be presented to the Centre Scientifique et Technique du Bâtiment.
Details of the extent, nature and frequency of testing and controls to be performed within the factory production control shall correspond to the test plan which is part of the technical documentation of this European Technical Approval.
For initial type testing, the results of the tests performed as part of the assessment for the ETA can be used unless there are changes in the production line or plant. In such cases, the necessary initial type testing has to be agreed between the “Centre Scientifique et Technique du Bâtiment” and the Notified Bodies involved.
3.3 CE-Marking
The CE marking shall be affixed on the commercial documents accompanying the components of the system. The symbol « CE » shall be accompanied by the following information: - name or identifying mark of the producer, - the last two digits of the year in which the CE-marking was affixed, - number of the European Technical Approval, - Veture kit identification (trade name), - Reaction to fire.
1)
The test plan has been deposited with the Centre Scientifique et Technique du Bâtiment and is only made available to the approved bodies involved in the conformity attestation procedure.
Page 15 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Example of CE marking and accompanying information:
Letters "CE"
Any Company
Street 1, City,
Country
Name and address of the producer (legal entity responsible for the
manufacture)
08 Two last digits of year of affixing CE marking
ETA-08/..... ETA number
ETAG 017 ETAG number (where relevant)
Reaction to fire: Euroclass F
Watertightness: type I
Type / intended use / use category / declared values and/or classes
in accordance with section(s) ... of the ETA
Page 16 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
4 Assumptions under which the fitness of the product for the intended use was
favourably assessed
4.1 Manufacturing
The components of the Veture kit are manufactured in accordance with the provisions of the European Technical Approval using the automated manufacturing process as identified during inspection of the plant by the Centre Scientifique et Technique du Bâtiment and the approved body and as laid down in the technical documentation.
4.2 Installation (fig. 5 to 14)
4.21 General
It is the responsibility of the ETA-holder to guaranty that the information about design and installation of the Veture kit are effectively communicated to the concerned people. These information can be given using reproductions of the respective parts of the European Technical Agreement. Besides, all the data concerning the execution shall be clearly indicated on the packaging and/or the enclosed instruction sheets using one or several illustrations.
In any case, it is suitable to comply with the national regulations and particularly concerning fire and wind load resistance.
Only the components described in paragraph 1.1 with characteristics according to paragraph 2 can be used.
4.22 Design
The choice and the rate of the fixings shall be determined considering:
the design wind load suction and the national regulations (taking into account the national safety factors, the design rules, …),
the characteristic resistance of the anchors into the considered substrate,
safety in use of the Veture kit (cf. § 2.2.3).
4.23 Execution
The diagnostic and design of the substrate as well as the generalities about the execution of the Veture kit shall be carried out in compliance with:
- chapter 7 of the ETAG 017, - national regulations applicable.
Page 17 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
5 Recommendations
5.1 Packaging, transport and storage
Packaging of the components are such that the products are protected from moisture during transport and storage, unless other measures are foreseen by the manufacturer for this purpose.
The components must be protected against damage.
5.2 Maintenance and repair of the works
It is assumed that the Veture kit shall normally be maintained in order to fully preserve their performances.
Maintenance includes:
- the repairing of localised damaged areas due to accidents (see Annex 5),
- the application of various products or paints, possibly after washing or ad hoc preparation.
- necessary repairs should be done rapidly.
Comment: Care should be taken to use products which are compatible with the Veture kit.
Director Technique Charles BALOCHE
Page 18 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
FIGURES
Profil 1 (Old version) Profil 2 (New version)
Figure 1 – Veture unit
Page 19 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 2 –aluminium profiles
Figure 2bis – First profile
Page 20 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 3 – Fixing
Figure 4 – Position of fixing
Page 21 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 5 – Vertical junction of the elements without profile
Figure 6 – Vertical junction of the elements with T profile
Page 22 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 7 – Horizontal junction of the old version elements with T or H profile
Page 23 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 7bis - Horizontal junction of the new version elements with T or H profile
Page 24 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 8 – Installation of the first units
Page 25 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 9 – Installation of the first units (continuation)
Page 26 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 10 – Drill and fixing
Figure 11 – Installation of the second line of units
Page 27 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 12 – Example of installation of square units
Figure 13 – Example of installation of high units with H profile
Page 28 of European Technical Approval VETISOL MODULPIERRE - ETA-09/0041 Validity from 30/05/2013 to 30/05/2018
Figure 14 – Example of installation of high units with T profile