Pocket Oscilloscope
32비트 ARM Cortex-M3 호환 비트 플랫폼에 기반을 갖춘 소형 Oscilloscope
로서 일반적인 전자 기기 (에어컨 또는 산업 주파수 인버터의 전원 공급
장치, AC / DC 전원 공급 장치 또는 인버터, 엘리베이터 및 건물에 소방
설비, 산업 현장 제어 회로 스위칭), 하드웨어 유지 보수 또는 소프트웨어
인터페이스 회로검사, Supply 전자 회로, 신호 분석 등에 이용하여 보다
효율적이고 편리하게 진행할 수 있도록 도와드립니다.
ARM Cortex – M3코어를 사용한
DS0201
DS0201
1http://www.hanjindata.com/
본 구성 물품에 micro SD card는 제외됩니다 (2G micro SD 카드를 사용해
주시기 바랍니다.)
DS0201
DSO 구성물품
이건 전원 스위치버튼입니다. 잃어버리지 마십시오!
2http://www.hanjindata.com/
DSO 제품 사양
DS0201
디스플레이 2.8” 컬러 TFT LCD
디스플레이 해상도 320 X 240
디스플레이 색상 65K
아날로그 대역폭 0 -1MHz
최대 샘플 속도 1Msps 12Bits
샘플 메모리 깊이 4096 포인트
수평 감도 1uS/Div (1-2-5 단계)
수평 위치 표시기 조절
수직 감도10mV/Div ~ 10V/Div (with x 1 probe)
0.5V/Div ~ 10V/Div (with x 1 probe)
수직 위치 표시기 조절
입력 임피던스 500KΩ 이상
최대 입력 전압 80Vpp (by x 1 probe)
커플링 직류 (DC)
삼각법 모드 Auto, Normal, Single, 실시갂 스캔
기능
자동 측정 : 주파수, 주기, 의무, Vpp, VRAM, Vavg과 DC 전압
정확한 마크와 함께 수직 측정 가능
정확한 마크와 함께 수평 측정 가능
상승 / 하강 엣지 트리거
삼각법 레벨 표시기와 조절
삼각법 감도 조절 표시기
일시정지, 플레이 기능
테스트 신호 10HMz ~ 1MHz (1-2-5 단계) 내장
파형 저장 SD card
USB를 통한 PC연결 SD card 리더
업그레이드 Bootloader USB
전원 공급 3.7 리튬 Battery 공급장치 / USB
치수 (I / O probe) 105 mm X 53 mm X 8 mm
http://www.hanjindata.com/ 3
LCD Display Information
DS0201
Basic usage
The UI could be divided to 4 parts: main menu (top), functions (right column), status bar
(bottom), and waveform & markers displays. Use cursor ↑ , ↓, ←, → to navigate among the
three operational parts and make adjustments.
Waveform & Markers
Green waveform – current signal being monitored
Purple waveform – reference waveform loaded from SD card.
Voltage measure marker V1 and V2 (Dot, vertical) – A voltage measure value between
V1-V2 could be displayed.
Time measure marker A and B (Dot line, horizontal) – A time measure value between A
and B could be displayed.
Y positions marker (Purple) – Y position center line for adjustment reference
Trigger level marker (Yellow) – Used to set trigger level
Menu
Horizontal main menu on top of screen, Navigate by ←, → adjust by ↑, ↓.
http://www.hanjindata.com/ 4
DS0201
사용법
Sync. Mode : When blinking, press ↑and ↓to select 4 different synchronization
mode: AUTO, NORM, SING, and NONE.
Auto - Automatic synchronous sweeping mode, displays waveform even not triggered.
Normal - Normal synchronous sweeping mode, displays whenever trigged.
Single – Single sweeping mode, display when triggered, then stopped with latest
Triggered waveform.
NONE – Random sampling mode
SCAN – Scan mode, to check long period low frequency signal.
Vertical Scale : When blinking, press ↑ and ↓ to select different level of sensitivity.
Total 19 scales are optional from 10mV/Div to 100V/Div. Note 1: If you use scale above
20V/Div, please use probe with attenuation of 10:1). Note 2: If newly set scale does not
match reference waveform, the latter will be cleared.
Horizontal sensitivity : When blinking, press ↑ and ↓ to select different sensitivities. ,
from 1uS/Div to 10S/Div total 22 grades. Note 2: If newly set sensitivity does not match
reference waveform, the latter will be cleared.
Y position : When blinking, press ↑ and ↓ to adjust the vertical position of the waveform. Press
„M‟ to hide/activate Y position marker if needed.
Calculation Mode : Auto calculation modes include:
FREQN – Signal frequency
CYCLE – Signal period
DUTY – Duty time
Vpp – AC signal peak-peak value
Vram – AC signal effective value
Vavg – AC signal average value
DC.V – DC signal average value.
Power supply mode : Power supply by internal battery or USB port. Battery bar will be displayed
when powered from internal.
http://www.hanjindata.com/ 5
DS0201
Functions
Vertical function buttons on side of screen, Navigate by ↑, ↓ adjust by ←, →.
Trigger sensitivity : When blinking, press ← and → to adjust trigger sensitivity, trigger level
marker (Yellow dotted area) changes correspondingly.
Trigger Type : When blinking, press ← and → to choose trigger mode of rising edge or falling
edge.
Probe attenuation scale : When blinking, press ← and → to choose 1:1 or 1:10 probe.
Save waveform : When blinking, status bar will display “ Save Filexxx”, press ← and → to select
file name with xxx = 000-255. Press „M‟ to save current waveform on display to SD card.
Load waveform : When blinking, status bar will display “ Save Filexxx”, press ← and → to select
file name with xxx = 000-255. Press M to load current waveform to display from SD card.
Note : current version has no file creation function, a FILEXXX.DAT must be prepared
by connecting to PC by USB.
Ref. square wave freq. : When blinking, press ← and → to adjust the frequency of reference
square wave.
Horizontal position adj. : When blinking, press ← and → to scroll waveform horizontally.
Index Bar : Show current display position of total loaded wavefrom
Status Bar
Time markers .: When blinking, press ← and → to adjust T1 or T2 time measure marker, the
time difference PT=T1-T2 will be displayed.
Voltage markers : When blinking, press ← and → to adjust V1 or V2 time measure marker, the
Voltage difference PV=V1-V2 will be displayed.
Trigger level : When blinking, press ← and → to adjust trigger level, trigger level marker (Yellow
dotted line) changes correspondingly.
Save Settings
Hold “R/S” Button and press “M” button to save current settings as default.
http://www.hanjindata.com/ 6
DS0201
http://www.hanjindata.com/ 7
DS0201
Firmware Upgrade
DfuSe_Demo.exe (Download Program)
펌웨어 업그레이드를 위해서는 DfuSe라는 프로그램이 필요합니다
http://www.st.com/stonline/products/support/micro/files/um0412.zip
위 파일을 다운로드하고 순서대로 Next를 클릭하여 설치하십시오.
DfuSe Driver 설치
DfuSe 설치가 다 끝나면 보드와의 연결을 위해서 Driver 설치를 해야 하는데 먼저 (전원 Off 상태에
서
제품의 화살 키 ↓를 누르면서 전원을 키면
위 사짂과 같은 화면이 LCD에 출력되면서 플러그 인 플러그가 실행되면서 새 하드웨어 발견이라는
문구가 떠오르면서 새 하드웨어 검색 마법사 시작이 실행됩니다 Next를 누릅니다.
http://www.hanjindata.com/ 8
DS0201
Next를 눌러 계속 짂행합니다.
짂행하다 보면 다음과 같은 메시지가 뜨면서 설치가 멈추는 데 화면에 체크된 빨갂 박스를 따라가면
별다른 어려움 없이 설치할 수 있습니다.
STTub30.sys file 경로를 지정해주고 확인버튼을 눌러주면 보드와 PC가 연결됩니다.
http://www.hanjindata.com/ 9
DS0201
Firmware Upgrade
여기까지 짂행과정을 문제없이 해왔다면 DfuSe_Demo를 실행시켜 봅니다.
프로그램이 실행되면 상단 1번에 현재 연결되어 있는 보드가 자동으로 검색되어 설정됩니다.
주의할 점은 2번으로 반드시 체크해주어야 버퍼 후에 다운로드 하게 됩니다.
3번은 미리 다운 받은 Firmware file을 선택하는 하는 것이고 선택 후에 4번 버튼을 누르면 자동으로
Upgrade가 실행됩니다.
⑴
⑵
⑶ ⑷
http://www.hanjindata.com/ 10
A/S & 제품기술문의
한진데이타 기술지원팀Fax: 032) 263-7563Email : [email protected]
DS0201
위 화면과 같은 과정을 거쳐 성공 메시지가 뜨면 Upgrade된 것입니다.