2010 Chevrolet Camaro Rs Mesh Grille Carid

8/8/2019 2010 Chevrolet Camaro Rs Mesh Grille Carid

1/8


2/8

3. You must mark the location of the hood latch assembly,then use a 13mm wrench to remove it from the core sup-port. This will give you adequate room for Mesh Grilleinstallation.

2

4. Use a large flat blade screwdriver to remove the factorybow tie emblem from the factory grille. This is not an easystep, but with patience you will be able to remove theemblem by inserting the screwdriver between the emblemmounting tabs and the grille and twisting back and forth.

This opens up the mounting slots in the grille.

4

Copyright 2009 by E&G Classics, Inc.

5

5. These are the outer tabs that you need to push down onto remove the emblem (one per side).

2. Remove the factory push fasteners from across the frontedge of the bumper cover by lifting up on the top portionof the push fastener until it rises approximately 1/2 (seeinset photo), then pull the entire push fastener up and outof each mounting hole. Once all the push fasteners havebeen removed, lift the panel out of the way for hoodcatch removal.

2

*************1412-0034-10R1412-0020-10BI1999-0301-00

*************1412-0022-10SS1412-0021-10SSBI1999-0301-001999-0311-001412-0035-101412-0036-101412-1902-10R1999-0256-001999-0273-001999-0065-001999-0264-00

1412-0158-101412-0159-101412-0069-101412-0068-103004-9250-921412-0068-10SS3004-9244-923999-9026-001999-9555-001999-9072-00

Description Part No.QuantitySS Black Ice Part #1412-B102-10SSRUpper Fine Mesh Grille (includes):Chrome Plated SurroundBlack Ice Mesh Section(4) 5 Black Cable Ties

Lower Fine Mesh Grille (includes):Stainless Steel SurroundBlack Ice Mesh Section(4) 5 Black Cable Ties(5) #8 x 1-1/4 Black Cap plugs22 Gage Polished S.S. Fillers RightLeftHardware Kit (components listed below):(4) Small Black plastic Washers(6) 5/16 PVC Spacers(16) #8-32 ESNA Half Nuts(10) 1.006 x.189 x.062 Black Plastic Washers

(1) Bow Tie Emblem Backing Plate(1) Logo Emblem Backing Plate(1) Emblem Hole Location Template(1) Mounting Hole Location Template(42) .045 x .250 Double Faced Tape(1) SS Lower Hole Location Template(6) .045 x 1 Double Faced Tape(4) #6 x 1/2 Countersunk Phillips Screws(1) #10 Lock Washer(1) #8-32 S.S. Hex Nut

1

1

1 Set1

6. Apply protective masking tape around the edges of theheadlight assemblies, upper and lower grille openings toprotect the painted bumper cover.

6


3/8

Copyright 2009 by E&G Classics, Inc.3

11. Cut off the closed ends from the preinstalled lower grilleblack cap plugs and push the sleeves down over the

mounting studs (as shown). The sleeves are used on thebottom studs only. Remove all other sleeves.

11

8. For SS models: Use a 5/16 drill bit to drill through themarks made in the plastic lower grille prior to grille align-ment.

10. Cut two (2) 6 long pieces of 2 x 4 and use them to holdthe bottom edge of the bumper cover down for lowergrille mounting hardware access.

9. Remove the two (2) lower 10mm factory bolts fromunderneath the bumper cover.

8

10

9

7. For SS models: Cut out and align the lower hole loca-tion template onto the lower grille in the bumper coveropening and use masking tape to hold it in place. Use anawl or similar pointed tool to mark the hole locationonto the plastic grille (as shown). Untape the template,flip it over and mark the opposite side.

7

12. Align the lower mesh section and surround into place,making sure the outer studs pass through the holesdrilled in Step 8.


4/8

13. Install the supplied small black plastic washers and #8-32 ESNA half nuts to the outer studs and completelytighten. DO NOT OVERTIGHTEN or you could damagethe lower grille surround by indenting it at the stud loca-tions.

14. Install the 1.006 x .189 x .062 black plastic washersand #8-32 ESNA half nuts onto the remaining studs andtighten. DO NOT OVERTIGHTEN or you could damagethe lower grille surround by indenting it at the stud loca-tions.15. Once the lower grille is installed, remove the 2 x 4 sec-tions and reinstall the two 10mm bolts removed in Step9.

14

13


17. Reinstall the front license plate bracket (if equipped).

17

18. Cut out and align the supplied templates, taping them inplace. Use an awl or similar pointed tool to make thecenters of the hole locations onto the factory grille.

16. Use a grease pencil to mark the areas that need to betrimmed on the front license plate bracket (as shown).Use a small disc grinder to remove the section of thebracket (cross hatched areas) that would interfere withreinstallation.

16

2010ChevroletCamaro

EmblemMountingPlate

Hole LocationTemplate

Part #1412- 0069-10

18

19. The small template will be used on the verticle grille finsas well, top and bottom aligned (bottom shown).

19


5/8


20. Use a .125 (1/8) drill bit and drill through the marksmade in the previous steps.

IMPORTANT: Apply multiple layers of masking tape to thepainted bumper cover at the areas that the factory grillewill be drilled. Drill carefully and DO NOT ALLOW THE

DRILL CHUCK TO MAKE CONTACT WITH THE PAINTEDBUMPER COVER !

21. Enlarge the holes to 5/16, then use the drill bit to con-nect the holes, creating a mounting slot. Once all themounting holes have been drilled, blow out the holesand front of the vehicle to remove any plastic shavingsthat could get caught between the mesh and factorygrilles.

2120

25. Prior to grille installation, align and install the emblemassembly onto the mesh grille in the approximate place itwas on the factory grille using the supplied large blackplastic washer, #10 lock washer and a #8-32 hex nutand tighten until the emblem is snug. The tape will keepthe emblem from rotating.

25

23. For RS & SS models: Adhere the emblem to the sup-plied logo backing plate (SS shown).24. Install .045 x 1 double faced tape onto the back of the

emblem mounting plate and remove the liner (whereshown, see arrows).

22. For RS & SS models: Remove any remaining factoryadhesive tape from the back of the factory emblem.Install and trim the supplied .045 x 1 double facedtape to the back of the emblem (RS shown).

24

26. Align the mesh and surround into place, making sure allstuds have passed through the holes drilled in the previ-ous steps. Install the supplied 5/16 PVC spacers and #8-32 ESNA half nuts. All six (6) studs will require the use ofthe supplied spacers. Hand tighten the ESNA nuts onlyat this time!

26

IMPORTANT


6/8


27. Use cutters to remove the mesh retaining wire ties, thentighten the mounting hardware.

27

28. Align the emblem mounting plate over the back of thefactory grille emblem, making sure all the factory mount-ing tabs pass through the slots in the mounting plate.

29. Using a small flat blade screwdriver, fit the tip down intothe small slot cut into the tab (as shown).

29

30. Bend the retaining tabs towards the factory mountingtabs until they hook underneath, locking the emblem tothe mounting plate.

30

31. Close up of the retaining tab properly bent to engagethe factory mounting tab, keeping the emblem tightagainst the mounting plate.32. Bend all remaining tabs to secure the emblem to the

mounting plate (not shown).

31

33. Align the emblem assembly into place, making sure allstuds have passed through the holes drilled in the previ-ous steps. Install the supplied small black plastic washersand #8-32 ESNA half nuts to secure the emblem assem-bly.

33


7/8


34. Apply multiple layers of masking tape to the bumpercover at the outer mounting hole locations. Carefully drillthrough the outer grille mounting holes using a 1/16drill bit. Use extreme caution and DO NOT LET THEDRILL CHUCK HIT THE BUMPER COVER or NICK THECHROME MESH SURROUND !

34

35. Push in on the grille surround and install the supplied#6 x 1/2 countersunk phillips screws but DO NOTOVERTIGHTEN. Over tightening will strip out the

mounting holes!

35

36. Remove the protective masking tape from around themesh grilles. Peel the tape back over itself to minimize

breakage.

36

37. Once the internal grille mounting hardware is tight, rein-stall the hood latch assembly by aligning the assembly tothe marks made in Step 3 and installing and tighteningthe factory 13mm hex bolts.

37

38. Install the supplied .045 x .250 double faced tape to theback of the stainless steel overlays as shown. 39. Peel back a small section of the double faced tape linerfrom each piece ofdouble faced tape and fold it over.40. Carefully align the overlay so that the edges are flush

with the mesh surround. Once properly aligned, beginpressing on the overlay while pulling off the remainingtape liner. Once all the liner has been removed, firmlypress the overlay into place to set the tape.

39


8/8

Documents

2010 Chevrolet Camaro Rs Mesh Grille Carid